Российский Клуб Chevrolet TrailBlazer & Chevrolet Tahoe

Автор Тема: КОДЫ ОШИБОК OBD 2 ===расшифровка и решение проблем===  (Прочитано 382886 раз)

0 Пользователей и 2 Гостей просматривают эту тему.

Military

  • Ст. Лейтенант
  • *
  • Оффлайн Оффлайн
  • Возраст: 53
  • Пол: Мужской
  • Сообщений: 606
  • Автомобиль: Trailblazer 2006г.
  • Имя: Юрий
  • military69
  • Местоположение: Мурманск
  • Карма: +30/-0

Спасибо!
Теперь еще и с переводом мучаюсь!:)
Записан

Виталий

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 47
  • Пол: Мужской
  • Сообщений: 4943
  • Автомобиль: ТБ, 2005
  • Имя: Виталий
  • Местоположение: МО г. Подольск
  • Карма: +211/-4

Спасибо!
Теперь еще и с переводом мучаюсь!:)

Установи Гугл Хром (браузер) он автоматически переводит почти со всех языков
Записан
Бываю редко, если что пишите в личку.......

Military

  • Ст. Лейтенант
  • *
  • Оффлайн Оффлайн
  • Возраст: 53
  • Пол: Мужской
  • Сообщений: 606
  • Автомобиль: Trailblazer 2006г.
  • Имя: Юрий
  • military69
  • Местоположение: Мурманск
  • Карма: +30/-0

Спасибо!
Установил, перевел, прочитал и понял что не хрена не понял!:)
Ясно одно что все же  плохая работа топливного насоса может являться следствием тех геморов которые меня имеют.Но откуда тогда дико повышенный расход топлива на холостых оборотах. Обороты в норме, температура тоже!Но куда проваливается 52 с копейками литра на сотню по компьютеру, понять не могу, бензапровод в норме, бак целый. И понять не могу почему на трассе расход идет привычный в районе 15 литров., по городу 23, это все на полном приводе и в морозы до -35
Записан

Military

  • Ст. Лейтенант
  • *
  • Оффлайн Оффлайн
  • Возраст: 53
  • Пол: Мужской
  • Сообщений: 606
  • Автомобиль: Trailblazer 2006г.
  • Имя: Юрий
  • military69
  • Местоположение: Мурманск
  • Карма: +30/-0

Всем кто остался не безучастным к моей проблеме_СПАСИБ О!
Разобрался!Сто процентный правильный совет дал GooLYVER!
Оказалось, причина в разгерметизации воздушной системы и некорректной работе первой лямды. Вылечили просто. Патрубок надели на место, новую лямду заказал, но и на старой пока проблем не возникает и чек не горит.Разобрали сь и нормально посмотрели только на четвертом сервисе.:(
Жалко что нормальных сервисов совсем мало,а официалы гнут цены и плюс левые причины выдумывают.:(
Записан

Виталий

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 47
  • Пол: Мужской
  • Сообщений: 4943
  • Автомобиль: ТБ, 2005
  • Имя: Виталий
  • Местоположение: МО г. Подольск
  • Карма: +211/-4

Может кому поможет.

Полгода ездил с ошибками по системе EVAP, помпа не работала и какой то клапан (номера ошибок не помню). Скидывание сканером помогало до первого холодного пуска.

Все полгода аккумулятор был мягко сказать на последнем издыхании (30-40 мин музыки или 1 час вставленного ключа его убивали напрочь) В морозы он здох окончательно и был заменен на новый и более мощный. Уже 2 недели езжу ошибок никаких нет, чек не загорается!!!
Записан
Бываю редко, если что пишите в личку.......

Bermakc

  • Ст. сержант
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 128
  • Местоположение: Пермский край
  • Карма: +2/-0

Прошу помощи.
на 150км истратил 70 литров бенза. По компу расход показыват 20литров.
Изменений в поведении не обнаружено.
Ошибки нашёл Р2101 и Р2176.
Что же это?
Записан

Bermakc

  • Ст. сержант
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 128
  • Местоположение: Пермский край
  • Карма: +2/-0

Ну может есть мысли у кого-нибудь? А то с таким потреблением бензы, я скоро в трубу вылечу...
Записан

GooLYVER

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 48
  • Пол: Мужской
  • Сообщений: 3508
  • Имя: Сан Саныч
  • ломаю L200/FX35 по очереди ~
  • Местоположение: МО по Ярославке
  • Карма: +1918/-983

Ну может есть мысли у кого-нибудь?

А что у Вас с погодой? Может обмерзание дросселя или его привода? (Обе ошибки по блоку дроссельной заслонки).
Записан
Есть технические вопросы? Пишите на broadway@land.ru.

Bermakc

  • Ст. сержант
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 128
  • Местоположение: Пермский край
  • Карма: +2/-0

погода  устаканилась. Ночью -25, днём -9!
Работа двигла не изменилась СОВСЕМ. Всё осталось как прежде, ток жрать стал как табун...
Но ошибки то на что указывают? И вообще, что там в др.заслонке может такое произойти? ;) 
А бензинком то и не пахнет нигде, я уж и снизу и с заду понюхал :)

Записан

GooLYVER

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 48
  • Пол: Мужской
  • Сообщений: 3508
  • Имя: Сан Саныч
  • ломаю L200/FX35 по очереди ~
  • Местоположение: МО по Ярославке
  • Карма: +1918/-983

ошибки указывают на то, что некорректно работает привод дроссельной заслонки.
Записан
Есть технические вопросы? Пишите на broadway@land.ru.

Bermakc

  • Ст. сержант
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 128
  • Местоположение: Пермский край
  • Карма: +2/-0

Всё исправилось! Виновата была холодная погода!
Записан

Maxtraxx

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 47
  • Пол: Мужской
  • Сообщений: 150
  • Карма: +2/-0

Периодически загорается чек день погорит погаснет, через неделю опять загорится -погорит-погорит - и гаснет. Сканером неоднократно проверяли: Р0106 - глючит датчик абсолютного давления (out of measure или что-то вроде). Сегодня опять. Показатели давления при заглушенном двигателе 98-99 кПа, на холостых - 28-30 кПа, при нажатии на газ резко уувеличивается до 100, потом падает до 40-20 кПа.Кто подскажет как правильно должен работать этот самый датчик и где конкретно он находится?
Записан

Павел600

  • Рядовой
  • *
  • Оффлайн Оффлайн
  • Возраст: 42
  • Пол: Мужской
  • Сообщений: 11
  • Автомобиль: Kia Cerato Koup
  • Имя: Павел
  • Местоположение: москва СЗАО
  • Карма: +0/-0

Всем привет. ребята подскажите по ошбке РО894. кроме того что автомат заблокируется, чем это может еще грозить?
Записан

kriolog

  • Ст. Лейтенант
  • *
  • Оффлайн Оффлайн
  • Возраст: 43
  • Пол: Мужской
  • Сообщений: 624
  • Автомобиль: Tahoe
  • Имя: Сергей
  • Местоположение: Москва САО
  • Карма: +25/-6

Приветствую всех!
Подскажите что означают ошибки Р0113 и Р0117?
И как их лечить?
Заранее спасибо!
Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0

DTC P0106

DTC Descriptor

DTC P0106
Manifold Absolute Pressure (MAP) Sensor Performance
The intake flow rationality diagnostic provides the within-range rationality check for the mass air flow (MAF), manifold absolute pressure (MAP), and the throttle position (TP) sensors. This is an explicit model-based diagnostic containing 4 separate models for the intake system.
The throttle model describes the flow through the throttle body and is used to estimate the MAF through the throttle body as a function of barometric pressure (BARO), TP, intake air temperature (IAT), and estimated MAP. The information derived from this model is the MAF Performance Test.
The first intake manifold model describes the intake manifold and is used to estimate MAP as a function of the MAF into the manifold from the throttle body and the MAF out of the manifold caused by engine pumping. The flow into the manifold from the throttle uses the MAF estimate calculated from the above throttle model. The information derived from this model is the MAP Performance Test 1.
The second intake manifold model is identical to the first intake manifold model except that the MAF sensor measurement is used instead of the throttle model estimate for the throttle air input. The information derived from this model is the MAP Performance Test 2.
The fourth model is created from the combination and additional calculations of the throttle model and the first intake manifold model. The information derived from this model is the TP Performance Test.
The estimates of MAF and MAP obtained from this system of models and calculations are then compared to the actual measured values from the MAF, MAP, and the TP sensors and to each other to determine the appropriate DTC to fail. The following table illustrates the possible failure combinations and the resulting DTC or DTCs.

Conditions for Running the DTC

DTCs P0102, P0103, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0128, P0335, P0336 are not set.
The engine speed is between 400-8,192 RPM .
The IAT Sensor parameter is between -7°C to +125°C (+19°F to 257°F) .
The ECT Sensor parameter is between 70-125°C (158-257°F) .
This DTC runs continuously within the enabling conditions.
Conditions for Setting the DTC

The powertrain control module (PCM) detects that the MAP sensor pressure is not within range of the calculated pressure that is derived from the system of models for more than 0.5 second .

Action Taken When the DTC Sets

DTC P0106 is a Type B DTC.

Conditions for Clearing the MIL/DTC

DTC P0106 is a Type B DTC.

Diagnostic Aids

A wide open throttle (WOT) acceleration from a stop should cause the MAP sensor parameter on the scan tool to increase rapidly to near the BARO Sensor parameter at the time of the 1-2 shift.
A skewed or stuck engine coolant temperature (ECT) sensor or IAT sensor will cause the calculated models to be inaccurate and may cause this DTC to run when it should not. Refer to Temperature Versus Resistance.
Circuit/System Verification

Important: Verify that the engine is in good mechanical condition before continuing with this diagnostic.

If DTC P0641 or P0651 are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle. See: Diagnostic Trouble Code Descriptions\Diagnostic Trouble Code (DTC) List - Vehicle
Verify the integrity of the entire air induction system by inspecting for the following conditions:
Any damaged components
Loose or improper installation
An air flow restriction
Any vacuum leak
Improperly routed vacuum hoses
In cold climates, inspect for any snow or ice buildup
Verify that restrictions do not exist in the MAP sensor port or vacuum source.
Verify that restrictions do not exist in the exhaust system. Refer to Restricted Exhaust. See: Engine, Cooling and Exhaust\Exhaust System\Testing and Inspection\Symptom Related Diagnostic Procedures\Restricted Exhaust
The BARO that is used by the engine control module (ECM) to calculate the air flow models is initially based on the MAP sensor at ignition ON. When the engine is running, the ECM will continually update the BARO value near WOT using the MAP sensor and a calculation. A skewed MAP sensor will cause the BARO value to be inaccurate. Determine the current vehicle testing altitude. Ignition ON, observe the scan tool BARO Sensor parameter. Compare the parameter to the Altitude vs Barometric Pressure table. Refer to Altitude Versus Barometric Pressure.
A skewed MAP sensor will also cause the first and second intake manifold models to disagree with the actual MAP sensor measurements. Use the scan tool and compare the MAP Sensor parameter to a known good vehicle, under various operating conditions.
Circuit/System Testing

Important: All electrical components and accessories must be turned OFF, and allowed to power down.

Ignition OFF, disconnect the MAP harness connector at the MAP sensor.
Ignition OFF, test for less than 5 ohms of resistance between the low reference circuit terminal A and ground.
¤   If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the PCM.
Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal C and ground.
¤   If less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the PCM.
¤   If greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the ECM.
Verify the scan tool MAP Sensor parameter is less than 12 kPa .
¤   If greater than the specified range, test the signal circuit terminal B for a short to voltage. If the circuit tests normal, replace the PCM.
Install a 3-amp fused jumper wire between the signal circuit terminal B and the 5-volt reference circuit terminal C. Verify the scan tool MAP Sensor parameter is greater than 103 kPa .
¤   If less than the specified range, test the signal circuit terminal B for a short to ground or an open/high resistance. If the circuit tests normal, replace the PCM.
If all circuits test normal, test the MAP sensor. Refer to Component Testing for instructions.
Component Testing

Important: You must perform the Circuit/System Testing in order to verify the integrity of the MAP sensor circuits before proceeding with the Component Testing.

Ignition ON, remove the MAP sensor.
Install a 3-amp fused jumper wire between the 5-volt reference circuit terminal C and the corresponding terminal of the MAP sensor.
Install a jumper wire between the low reference circuit terminal A of the MAP sensor and ground.
Install a jumper wire at terminal B of the MAP sensor.
Connect a DMM between the jumper wire from terminal B of the MAP sensor and ground.
Install the J35555 to the MAP sensor vacuum port. Slowly apply vacuum to the sensor while observing the voltage on the DMM. The voltage should vary between 0-5.2 volts , without any spikes or dropouts.
¤   If the voltage is not within the specified range or is erratic, replace the MAP sensor.
Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure. See: Verification Tests and Procedures

Manifold Absolute Pressure Sensor Replacement
Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0

DTC P0894 (4.2L)

Circuit Description

The powertrain control module (PCM) monitors the difference between engine speed and transmission output speed. In D3 drive range with the torque converter clutch (TCC) engaged, the engine speed should closely match the transmission output speed. In D4 drive range, with the TCC engaged, the TCC slip speed should be -20 to +50 RPM.

When the PCM detects excessive TCC slip when the TCC should be engaged, then DTC P0894 sets. DTC P0894 is a type B DTC.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0894 Transmission Component Slipping

Conditions for Running the DTC

No TP sensor DTCs P1120 or P1220.
No VSS DTCs P0502 or P0503.
No TCC solenoid valve DTC P0740.
No 1-2 SS valve DTC P0753.
No 2-3 SS valve DTC P0758.
No 3-2 SS valve assembly DTC P0785.
No TFP manual valve position switch DTC P1810.
No TCC PWM solenoid valve DTC P2761.
The engine speed is greater than 450 RPM for 5 seconds.
The engine is not in fuel cutoff.
The engine torque is 68-542 N.m (50-400 lb ft).
The TP angle is 20-99 percent.
The vehicle speed is 48-131 km/h (30-82 mph).
The engine speed is 1,500-3,000 RPM.
The speed ratio is 0.69-0.88 , speed ratio is engine speed divided by the transmission output speed.
The gear range is D4.
The commanded gear is not 1st gear.
The TFT is 20-150°C (68-302°F).
The shift solenoid performance diagnostic counters are zero.
Conditions for Setting the DTC

DTC P0894 sets if the following conditions occur for 3 TCC cycles.

The TCC is commanded ON for 5 seconds.
The TCC is at 40 percent duty cycle for 5 seconds.
The TCC slip speed is 130-800 RPM for 7 seconds.
Important: The following actions may occur before the DTC sets.

If the TCC is commanded ON for 5 seconds, the TCC is at 40 percent duty cycle for 5 seconds, the TP angle is 20-99 percent and the transmission slip counter has incremented to either 1 or 2, out of 3 to increment the fail counter for the current ignition cycle, then the following slip conditions and actions may increment the fail counter for the current ignition cycle: These conditions must occur sequentially.
Condition 1

If the TCC slip speed is 130-800 RPM for 7 seconds, then the PCM will command maximum line pressure and freeze shift adapts from being updated.

Condition 2

If Condition 1 is met and the TCC slip speed is 130-800 RPM for 7 seconds, then the PCM will command the TCC Off for 1.5 seconds.

Condition 3

If Condition 2 is met and the TCC slip speed is 130-800 RPM for 7 seconds, then the fail counter on the current ignition cycle is incremented.

The above slip conditions and actions may be disregarded if the TCC is commanded OFF at any time as a result of a driving maneuver, sudden acceleration or deceleration.

Action Taken When the DTC Sets

The PCM illuminates the malfunction indicator lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC are met.
The PCM commands maximum line pressure.
The PCM inhibits TCC engagement.
The PCM inhibits 4th gear if the transmission is in hot mode.
The TCM freezes transmission adaptive functions.
The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze Frame and Failure Records.
The PCM stores DTC P0894 in PCM history during the second consecutive trip in which the Conditions for Setting the DTC are met.
Conditions for Clearing the MIL/DTC

The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.
A scan tool can clear the MIL/DTC.
The PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without an emission-related diagnostic fault occurring.
The PCM cancels the DTC default actions when the fault no longer exists and/or the ignition switch is OFF long enough in order to power down the PCM.
Diagnostic Aids

Bronze material found in the transmission oil pan may indicate stator shaft bushing wear. If bushing wear is suspected, inspect the stator shaft and the input, turbine, shaft for damage.
Refer to Symptoms - Automatic Transmission for more information. See: Transmission and Drivetrain\Automatic Transmission/Transaxle\Testing and Inspection\Symptom Related Diagnostic Procedures\Symptoms - Automatic Transmission
Test Description

The numbers below refer to the step numbers on the diagnostic table.
This step tests the torque converter for slippage while in a commanded lock-up state.
Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0

DTC P0113

Circuit Description

The intake air temperature (IAT) sensor is a variable resistor. The IAT sensor has a signal circuit and a low reference circuit. The IAT sensor measures the temperature of the air entering the engine. The powertrain control module (PCM) supplies 5 volts to the IAT signal circuit and a ground for the IAT low reference circuit. When the IAT sensor is cold, the sensor resistance is high. When the air temperature increases, the sensor resistance decreases. With high sensor resistance, the PCM detects a high voltage on the IAT signal circuit. With lower sensor resistance, the PCM detects a lower voltage on the IAT signal circuit. If the PCM detects an excessively high IAT signal voltage, indicating a low temperature, DTC P0113 sets.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0112 Intake Air Temperature (IAT) Sensor Circuit High Voltage

Conditions for Running the DTC

DTCs P0117, P0118, P0125, P0502, P0503 are not set.
The engine run time is more than 5 minutes .
The vehicle speed sensor (VSS) indicates that vehicle speed is less than 24 km/h (15 mph) .
DTC P0113 runs continuously when the above conditions are met.
Conditions for Setting the DTC

The PCM detects that the IAT sensor parameter is less than -39°C (-38°F) for more than 6 seconds .

Action Taken When the DTC Sets

The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.
Conditions for Clearing the MIL/DTC

The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
Clear the MIL and the DTC with a scan tool.


Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0

DTC P0117

Circuit Description

The engine coolant temperature (ECT) sensor is a variable resistor, that measures the temperature of the engine coolant. The powertrain control module (PCM) supplies 5 volts to the ECT signal circuit and a ground for the ECT low reference circuit. When the ECT is cold, the sensor resistance is high. When the ECT increases, the sensor resistance decreases. With high sensor resistance, the PCM detects a high voltage on the ECT signal circuit. With lower sensor resistance, the PCM detects a lower voltage on the ECT signal circuit. If the PCM detects an excessively low ECT signal voltage, which is a high temperature indication, DTC P0117 sets.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0117 Engine Coolant Temperature (ECT) Sensor Circuit Low Voltage

Conditions for Running the DTC

The engine is running for more than 2 minutes .
DTC P0117 runs continuously when the above condition is met.
Conditions for Setting the DTC

The PCM detects that the ECT sensor parameter is more than 138°C (280°F) for more than 6 seconds .

Action Taken When the DTC Sets

The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.
Conditions for Clearing the MIL/DTC

The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
Clear the MIL and the DTC with a scan tool.
Записан

moose

  • Рядовой
  • *
  • Оффлайн Оффлайн
  • Возраст: 44
  • Пол: Мужской
  • Сообщений: 19
  • Автомобиль: Trailbalazer LT
  • Местоположение: СПБ
  • Карма: +0/-0

На днях загорелся чек, считали сканером показало р0410. Сняв клапан обнаружил в воздушных патрубках грамм 300 воды. Воду слил, проверил клапан и насос, все работает. Чек погас пока не загорается. Вопрос: как туда могла попасть вода, разве система не герметична?
Записан

StasAst

  • Ст. Лейтенант
  • *
  • Оффлайн Оффлайн
  • Возраст: 47
  • Пол: Мужской
  • Сообщений: 577
  • Автомобиль: TrailBlazer LTZ 2008- продан, Nissan Patrol 2012 !
  • Имя: Станислав
  • Танки грязи не бояться ! :-D
  • Местоположение: Астрахань
  • Карма: +24/-1

Да, интересный вопрос. Я был уверен, что система герметичная.
Записан

moose

  • Рядовой
  • *
  • Оффлайн Оффлайн
  • Возраст: 44
  • Пол: Мужской
  • Сообщений: 19
  • Автомобиль: Trailbalazer LT
  • Местоположение: СПБ
  • Карма: +0/-0

Сегодня опять чек загорелся, ошибка та же, насос на холодную включается, клапан открывается, что ей не нравится? Причем чек загорается, когда температура движка почти доходит до рабочей.
« Последнее редактирование: 06 апреля 2011, 11:36:59 от moose »
Записан

MiniOn

  • Ст. Прапорщик
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 271
  • Местоположение: Самара, Тольятти
  • Карма: +10/-4

Сегодня опять чек загорелся, ошибка та же, насос на холодную включается, клапан открывается, что ей не нравится? Причем чек загорается, когда температура движка почти доходит до рабочей.
видимо реле открытия-закрытия клапана не правильно работает. Это реле у нас стоит в самом мокром месте :(
У меня таже проблема. Заказл новое реле (1700р.), завтра поеду ставить. Возможно исправиться ошибка.
Записан

Alex7

  • Прапорщик
  • *
  • Оффлайн Оффлайн
  • Возраст: 47
  • Пол: Мужской
  • Сообщений: 204
  • Автомобиль: Chevrolet TrailBlazer
  • Местоположение: Псков
  • Карма: +7/-2

С периодичностью появляется ошибка Р0014 и сама исчезает на след день.
Что это?? как с этим жить ))) )))  ???


P0014 - ошибка системы изменения фаз. Загорается когда дельта между фактическим и заданным положением распредвала составляет более 3.5 градусов. Возможно неисправен или периодически зависает клапан изменения фаз, а может ратянута цепь или датчик положения распредвала периодически выдает неверные данные, а может глюк PCM или что-то еще - нужна более тщательная диагностика.
...авто стояла 2 недели, после запуска появилась такая же ошибка Р0014, подскажите номера з\ч, кто уже с этой ошибкой сталкивался, плиз..
Записан

Пенсионер

  • Майор
  • *
  • Оффлайн Оффлайн
  • Возраст: 68
  • Пол: Мужской
  • Сообщений: 812
  • Автомобиль: Chevrolet TrailBlazer 2004 № Х 757 ХА/57
  • Местоположение: г.Орел
  • Карма: +27/-2

Снимал и чистил на прошлой неделе клапан, грязи в нем было достаточно. Удалял кисточкой и растворителем 646. Собрал, посадил на место через герметик и три дня ездил с наслаждением. Сегодня утром при прогреве опять "джеки чан". Подскажите, кто знает в каком положении должна быть пластина внутри клапан?
Записан

moose

  • Рядовой
  • *
  • Оффлайн Оффлайн
  • Возраст: 44
  • Пол: Мужской
  • Сообщений: 19
  • Автомобиль: Trailbalazer LT
  • Местоположение: СПБ
  • Карма: +0/-0

Код клапана вторичной подачи воздуха 12619128 или 12575655, я отдал за оригинальный  чуть меньше пяти тысяч, поменял за 15 минут, завтра посмотрим.
Записан

kriolog

  • Ст. Лейтенант
  • *
  • Оффлайн Оффлайн
  • Возраст: 43
  • Пол: Мужской
  • Сообщений: 624
  • Автомобиль: Tahoe
  • Имя: Сергей
  • Местоположение: Москва САО
  • Карма: +25/-6

День добрый!
Кто-нибудь в курсе по ошибке Р1174?
Что означает?

Спасибо!
Записан

Alex7

  • Прапорщик
  • *
  • Оффлайн Оффлайн
  • Возраст: 47
  • Пол: Мужской
  • Сообщений: 204
  • Автомобиль: Chevrolet TrailBlazer
  • Местоположение: Псков
  • Карма: +7/-2

Код клапана вторичной подачи воздуха 12619128 или 12575655, я отдал за оригинальный  чуть меньше пяти тысяч, поменял за 15 минут, завтра посмотрим.
...спасибо!!!
Записан

МоНстриК

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Пол: Мужской
  • Сообщений: 3549
  • Автомобиль: ТБ. 2005 LTZ
  • Имя: Михаил
  • Местоположение: г.Щелково М.о
  • Карма: +228/-13

доброго времени многоуважаемые клубни. вот и я прошу помоши и совета,  у меня горит чек и показывает ошибку Р0410 и Р0496.  по симптомам заметил повышенный расход бензина и все двигло работает ровно  четко косяков вроде не наблюдается.  читая форум определил какая ошибка на что показывает, но как они связаны все таки не понимаю, и непойму ч чего начать, тут много писали и про продувку и про лямды и про клапан..  по лямде как понял былаб другая ошибка, по 0410 -продувка ката. снимал насос из под рамы и реле по отдельности они работают, как определить работают ли они на месте?? по 496 нужно смотреть клапан, открыт или закрыт открывается или закрывается( тут ясно , благо все расписано) в обшемто вопрос вот в чем : какая ошибка из какой вытекает Р0410 из Р0496 или наоборот, и исправив одну вторая должна уйти?
Записан

GooLYVER

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 48
  • Пол: Мужской
  • Сообщений: 3508
  • Имя: Сан Саныч
  • ломаю L200/FX35 по очереди ~
  • Местоположение: МО по Ярославке
  • Карма: +1918/-983

какая ошибка из какой вытекает Р0410 из Р0496 или наоборот, и исправив одну вторая должна уйти?

Не факт, он если ошибки вызваны одной неисправностью, то скорее всего имя этой неисправности - негерметичность (не одеты или повреждены патрубки или неисправен клапан).
Записан
Есть технические вопросы? Пишите на broadway@land.ru.

МоНстриК

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Пол: Мужской
  • Сообщений: 3549
  • Автомобиль: ТБ. 2005 LTZ
  • Имя: Михаил
  • Местоположение: г.Щелково М.о
  • Карма: +228/-13

спасибо Саш, я скорее склоняюсь к неисправности клапана..ладно поживем увидим
Записан