Российский Клуб Chevrolet TrailBlazer & Chevrolet Tahoe

Автор Тема: КОДЫ ОШИБОК OBD 2 ===расшифровка и решение проблем===  (Прочитано 382740 раз)

0 Пользователей и 2 Гостей просматривают эту тему.

TSV

  • Мл. сержант
  • *
  • Оффлайн Оффлайн
  • Возраст: 49
  • Пол: Мужской
  • Сообщений: 74
  • Местоположение: Москва ЮВАО
  • Карма: +4/-0



Да дохлая была
машину трясло троило
После замены ошибки сбрасывали? Чек сразу загорелся с P1133? Сейчас он горит постоянно или просто периодически появляется?
[/quote]

да все сбрасыввал
загорается не сразу а через какоето время
допустим вечером сбросил
а к вечеру след дня опять загорается
[/quote]

Новая лямда родная, на эту машину? Катализатор вырезан или нет?
Бывает что вторая тоже не исправна, но ошибок не выдаёт, но это лишь моё предположение, надо смотреть их показания, как меняются кривые во время езды.
Я бы пока поездил если расход и работа двигателя тебя устраивает, возможно к этой ошибке что-то ещё добавится там и делать выводы, ну ещё заправки поменять.
Записан
TB '04 LTZ

vitalo

  • Мл. Лейтенант
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 357
  • Местоположение: Питер-Купчино
  • Карма: +5/-0

А нет не укого распиновки лямд ?
Записан
TrailBlazer 2005 LTZ,около  100000 км

nalim83

  • Сержант
  • *
  • Оффлайн Оффлайн
  • Пол: Мужской
  • Сообщений: 92
  • Автомобиль: Cadillac Escalade 2011
  • Местоположение: Москва
  • Карма: +6/-0

 С периодичностью раз в три дня вылезает ошибка Р0440. Кто что подскажет по решению данной проблемы? ТВ 2-го года
Записан

-=SPb=- Nikolas

  • Ст. Лейтенант
  • *
  • Оффлайн Оффлайн
  • Возраст: 51
  • Пол: Мужской
  • Сообщений: 589
  • Автомобиль: TAHOE 900 (РОССИЯ-13) ; TAHOE 900 USA-2007
  • Местоположение: Санкт-Петербург, Купчино.
  • Карма: +8/-0

С периодичностью появляется ошибка Р0014 и сама исчезает на след день.
Что это?? как с этим жить ))) )))  ???
« Последнее редактирование: 02 ноября 2010, 09:02:24 от -=SPb=- Nikolas »
Записан

-=SPb=- Nikolas

  • Ст. Лейтенант
  • *
  • Оффлайн Оффлайн
  • Возраст: 51
  • Пол: Мужской
  • Сообщений: 589
  • Автомобиль: TAHOE 900 (РОССИЯ-13) ; TAHOE 900 USA-2007
  • Местоположение: Санкт-Петербург, Купчино.
  • Карма: +8/-0

Был У "Вадима" на Софийской, в списке ошибок, такой  у него нет  ???
Записан

-=SPb=- Nikolas

  • Ст. Лейтенант
  • *
  • Оффлайн Оффлайн
  • Возраст: 51
  • Пол: Мужской
  • Сообщений: 589
  • Автомобиль: TAHOE 900 (РОССИЯ-13) ; TAHOE 900 USA-2007
  • Местоположение: Санкт-Петербург, Купчино.
  • Карма: +8/-0

С периодичностью появляется ошибка Р0014 и сама исчезает на след день.
Что это?? как с этим жить ))) )))  ???
Ауу!! кто-ть!!!!!!
Записан

GooLYVER

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 48
  • Пол: Мужской
  • Сообщений: 3508
  • Имя: Сан Саныч
  • ломаю L200/FX35 по очереди ~
  • Местоположение: МО по Ярославке
  • Карма: +1918/-983

С периодичностью появляется ошибка Р0014 и сама исчезает на след день.
Что это?? как с этим жить ))) )))  ???

P0014 - ошибка системы изменения фаз. Загорается когда дельта между фактическим и заданным положением распредвала составляет более 3.5 градусов. Возможно неисправен или периодически зависает клапан изменения фаз, а может ратянута цепь или датчик положения распредвала периодически выдает неверные данные, а может глюк PCM или что-то еще - нужна более тщательная диагностика.
Записан
Есть технические вопросы? Пишите на broadway@land.ru.

-=SPb=- Nikolas

  • Ст. Лейтенант
  • *
  • Оффлайн Оффлайн
  • Возраст: 51
  • Пол: Мужской
  • Сообщений: 589
  • Автомобиль: TAHOE 900 (РОССИЯ-13) ; TAHOE 900 USA-2007
  • Местоположение: Санкт-Петербург, Купчино.
  • Карма: +8/-0

Спасибо!!!
Но где в Питере ее можно сделать???  ???
Насколько я понимаю, если цепь растянута (пробег 80 000) она должна греметь, наверно надо попробовать поменять датчик положения распреда. или почистить клапан? (где он???)
Записан

shaman66

  • Ст. Прапорщик
  • *
  • Оффлайн Оффлайн
  • Возраст: 60
  • Пол: Мужской
  • Сообщений: 239
  • Автомобиль: GM900 Калининград 2013гв
  • Имя: Алексей
  • Местоположение: Алтай, Омск
  • Карма: +4/-0

P0411 что то про впускной коллектор
P0496 что то про абсорбер
понимаю что ошибки меж собой взаимосвязаны.. .
сбрасываю а они опять появляются на следующий день практически... Куда лесть?
Записан

biker78

  • Полковник
  • *
  • Оффлайн Оффлайн
  • Возраст: 48
  • Пол: Мужской
  • Сообщений: 1219
  • Автомобиль: Hummer H2 `08
  • Имя: Сергей
  • Местоположение: Димитровград
  • Карма: +60/-2

Вот блин, ну понимаю, что поиском наверное для некоторых напряг, но тема то про ош.0496 даже закреплена в этом разделе.
http://trailblazerclub.ru/forum/index.php?topic=2237.0
Записан

GooLYVER

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 48
  • Пол: Мужской
  • Сообщений: 3508
  • Имя: Сан Саныч
  • ломаю L200/FX35 по очереди ~
  • Местоположение: МО по Ярославке
  • Карма: +1918/-983

Куда лесть?

P0411 вытекает из P0496.

Ошибка P0411 означает, что фактическое давление в системе EVAP отличается от расчетного более чем на 6 кРа. А ошибка P0496 конкретизирует неисправность, указывая на то, что клапан EVAP работает некорректно. Для начала смотрите клапан.
   Ошибка возникает только при холодном пуске, так что сбрасывая клемму Вы ничего не исправляете.

P.S. Прав Biker, тема уже раскрыта.
« Последнее редактирование: 25 ноября 2010, 10:52:07 от GooLYVER »
Записан
Есть технические вопросы? Пишите на broadway@land.ru.

shaman66

  • Ст. Прапорщик
  • *
  • Оффлайн Оффлайн
  • Возраст: 60
  • Пол: Мужской
  • Сообщений: 239
  • Автомобиль: GM900 Калининград 2013гв
  • Имя: Алексей
  • Местоположение: Алтай, Омск
  • Карма: +4/-0

Вот блин, ну понимаю, что поиском наверное для некоторых напряг, но тема то про ош.0496 даже закреплена в этом разделе.
http://trailblazerclub.ru/forum/index.php?topic=2237.0
спасибо за ссылку, что то сразу найти не получилось...
Записан

графит

  • Рядовой
  • *
  • Оффлайн Оффлайн
  • Пол: Мужской
  • Сообщений: 7
  • Автомобиль: шевроле Тахо
  • Местоположение: Москва
  • Карма: +0/-0

а никто не подскажет что означает ошибка Р1125, это как то связано с датчиком дроссельной заслонки?
Заранее спасиб :)
Записан

GooLYVER

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 48
  • Пол: Мужской
  • Сообщений: 3508
  • Имя: Сан Саныч
  • ломаю L200/FX35 по очереди ~
  • Местоположение: МО по Ярославке
  • Карма: +1918/-983

а никто не подскажет что означает ошибка Р1125, это как то связано с датчиком дроссельной заслонки?
Заранее спасиб :)

Других ошибок нет? Тогда скорее всего дело в педали газа, точнее в сенсоре на ней или в цепи педаль>TCM. Эта ошибка, "APP (accelrrator pedal position) system" возникает, когда обнаруживается расхождение между фактическим положением педали газа и сигналом с ее датчика. При этом не будет работать ETC (противобуксовоч ная система).
Если есть другие ошибки, то возможно дело и не в педали.
Записан
Есть технические вопросы? Пишите на broadway@land.ru.

-=SPb=- Nikolas

  • Ст. Лейтенант
  • *
  • Оффлайн Оффлайн
  • Возраст: 51
  • Пол: Мужской
  • Сообщений: 589
  • Автомобиль: TAHOE 900 (РОССИЯ-13) ; TAHOE 900 USA-2007
  • Местоположение: Санкт-Петербург, Купчино.
  • Карма: +8/-0

Спасибо!!!
Но где в Питере ее можно сделать???  ???
Насколько я понимаю, если цепь растянута (пробег 80 000) она должна греметь, наверно надо попробовать поменять датчик положения распреда. или почистить клапан? (где он???)

Поменял масло, ошибки (0014)    не было 3 месяца. щас опять загорелась ((  через 10 км погасла. ЧТО ЭТО??????
Записан

GooLYVER

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 48
  • Пол: Мужской
  • Сообщений: 3508
  • Имя: Сан Саныч
  • ломаю L200/FX35 по очереди ~
  • Местоположение: МО по Ярославке
  • Карма: +1918/-983

Поменял масло, ошибки (0014)    не было 3 месяца. щас опять загорелась ((  через 10 км погасла. ЧТО ЭТО??????

Похоже из-за смолистых отложений зависает клапан изменения фаз (№421 на картинке). Свежее масло немного промыло систему, из-за этого ошибка временно исчезла.  Можно снять и попробовать промыть (для снятия необходимо демонтировать насос ГУР-а)  -  возможно этого будет достаточно и замены не потребуется.

Записан
Есть технические вопросы? Пишите на broadway@land.ru.

-=SPb=- Nikolas

  • Ст. Лейтенант
  • *
  • Оффлайн Оффлайн
  • Возраст: 51
  • Пол: Мужской
  • Сообщений: 589
  • Автомобиль: TAHOE 900 (РОССИЯ-13) ; TAHOE 900 USA-2007
  • Местоположение: Санкт-Петербург, Купчино.
  • Карма: +8/-0

Спасибо огромное +1 после новогодних поеду к Вадиму. Так как в Питере больше ни кому не доверяю !!!!!!!!
Записан

Сургут

  • Ст. сержант
  • *
  • Оффлайн Оффлайн
  • Возраст: 46
  • Пол: Мужской
  • Сообщений: 124
  • Автомобиль: ТБ - 2005 г.черный .
  • Имя: Андрей
  • Местоположение: г.Сургут
  • Карма: +0/-3

Друзья помогите . Ошибки Р0017 , Р0420.
Записан

Dedywka Pin

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 39
  • Пол: Мужской
  • Сообщений: 4656
  • Автомобиль: TB LTZ 2014 2,8 D
  • Имя: Иван ;)
  • Dedywka Pin
  • Местоположение: Новосибирск
  • Карма: +107/-8

Подскажите сканер показал РО440А это тоже самое, что и P0440 Неисправность в системе контроля за отводом паров топлива.
Записан
По рзелульаттам илссеовадний одоного анлигйсокго унвиертисета, не иеемт занчнеия, вкокам пряокде рсапожолена бкувы в солве. Галвоне, чотбы преавя и пслоендяя бквуы блыи на мсете. Осатьлыне бкувы мгоут селдовтаь в плоонм бсепордяке, все-рвано ткест чтаитсея без побрелм. Пичрионй эгото ялвятеся то, что мы не чиатем кдаужю бкуву по отдльенотси, а все солво цликеом.

Blazer 1994 - Subaru Impreza Wagon 2000 - Nissan Primera 2001 - ТВ  LTZ 2002 модельный ряд 2003 + VW Passat 1997г. Citroёn C4L 2014, Lincoln Mark 8 1993, KIA Bongo 3 2009, Suzuki Grand Vitara 2014, ТВ  LTZ 2014г. 2.8

sirotka72

  • Капитан
  • *
  • Оффлайн Оффлайн
  • Возраст: 53
  • Пол: Мужской
  • Сообщений: 670
  • Автомобиль: ТБ 1 LTZ 2007 РЕСТАЙЛ КАЛИНИНГРАД
  • Не с нашим счастьем...
  • Местоположение: ...где-то на окраине вселеной...(Тобольск)
  • Карма: +11/-0

Поменял масло, ошибки (0014)    не было 3 месяца. щас опять загорелась ((  через 10 км погасла. ЧТО ЭТО??????

Похоже из-за смолистых отложений зависает клапан изменения фаз (№421 на картинке). Свежее масло немного промыло систему, из-за этого ошибка временно исчезла.  Можно снять и попробовать промыть (для снятия необходимо демонтировать насос ГУР-а)  -  возможно этого будет достаточно и замены не потребуется.


я снимал без демонтажа ГУРа
Записан
Не откладывай на завтра то, что можно отложить на послезавтра...

biker78

  • Полковник
  • *
  • Оффлайн Оффлайн
  • Возраст: 48
  • Пол: Мужской
  • Сообщений: 1219
  • Автомобиль: Hummer H2 `08
  • Имя: Сергей
  • Местоположение: Димитровград
  • Карма: +60/-2

Ну вот, опять ошибка, на этот раз С0055 - задний датчик скорости. При этом скорость показывает нормально, и оба из 2х задних датчиков скорости визуально в норме.
Кто нибудь сталкивался?
Записан

RocknRolla

  • Генерал армии
  • *
  • Оффлайн Оффлайн
  • Возраст: 45
  • Пол: Мужской
  • Сообщений: 2785
  • Автомобиль: Эскалейд 2009 г.
  • Имя: Руслан
  • Ростовчанин
  • Местоположение: Владикавказ (но уже скоро нет)
  • Карма: +192/-6

Байкер, проводку посмотри к нему. К датчику. Ее состояние.
Записан
But a RocknRolla, oh, he's different. Why? Because a real RocknRolla wants the fucking lot.

biker78

  • Полковник
  • *
  • Оффлайн Оффлайн
  • Возраст: 48
  • Пол: Мужской
  • Сообщений: 1219
  • Автомобиль: Hummer H2 `08
  • Имя: Сергей
  • Местоположение: Димитровград
  • Карма: +60/-2

Не понятно куда с них провода идут. Пробывал прозванивать до блока АБС под кузовом - туда точно не идут, хотя странно. Хотя если то смотрел - 2 датчика стоят на выходе с раздатки в кардан. Работают по индукционному принципу от крыльчатки. Сами датчики визуально тоже чистые, да и пачкаться им нечем. Местами их махнул - ничего не поменялось. Если бы проводка шалила - то стрелка скорости бы падала, но скорость показывает без перебоев и без ошибок...
Записан

biker78

  • Полковник
  • *
  • Оффлайн Оффлайн
  • Возраст: 48
  • Пол: Мужской
  • Сообщений: 1219
  • Автомобиль: Hummer H2 `08
  • Имя: Сергей
  • Местоположение: Димитровград
  • Карма: +60/-2

Ваще чудеса.
Прозвонил всю проводку к задним датчикам скорости, и от мозгов и от блока управления трансмиссией, и между мозгами и блоком АБС - все ОК.
Махнул датчики местами. Если бы какой то сдох, то ошибка бы стала другая, не по АБС, а по трансмиссии. Знгачит с ними тоже все ОК.
Взял с разборки другой блок АБС - вылезла ошибка по датчику АБС переднего правого колеса, а моя ошибка пропала. :) Этот новый блок вернул.
Взял с другой разборки блок АБС - вроде все пропало, но спустя 1 час езды (20 км :) ) СНОВА ПОЯВИЛАСЬ.

ЧТО ЗА ХРЕНЬ???
Проводка к датчикам в норме, датчики в норме, блок АБС другой - а ошибку показывает C0055/
« Последнее редактирование: 15 февраля 2011, 13:10:22 от biker78 »
Записан

-=SPb=- Nikolas

  • Ст. Лейтенант
  • *
  • Оффлайн Оффлайн
  • Возраст: 51
  • Пол: Мужской
  • Сообщений: 589
  • Автомобиль: TAHOE 900 (РОССИЯ-13) ; TAHOE 900 USA-2007
  • Местоположение: Санкт-Петербург, Купчино.
  • Карма: +8/-0

Поменял масло, ошибки (0014)    не было 3 месяца. щас опять загорелась ((  через 10 км погасла. ЧТО ЭТО??????

Похоже из-за смолистых отложений зависает клапан изменения фаз (№421 на картинке). Свежее масло немного промыло систему, из-за этого ошибка временно исчезла.  Можно снять и попробовать промыть (для снятия необходимо демонтировать насос ГУР-а)  -  возможно этого будет достаточно и замены не потребуется.


Блин, опять обороты гулять начали, машинка заглохла на ходу ((( еле оттормозился

 заглушил прошло 15 мин, все идеально даж чек погас (((
« Последнее редактирование: 15 февраля 2011, 12:56:24 от -=SPb=- Nikolas »
Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0

По ошибке С0550 есть следующие предложения в ALLDATA, может поможет:

 1.DTC C0550

Circuit Description

The electronic brake control module (EBCM) performs several self-tests for any internal problems which may affect proper operation.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC C0550 Electronic Control Unit (ECU) Performance

Conditions for Running the DTC

The ignition is ON.

Conditions for Setting the DTC

The EBCM detects an internal malfunction.

Action Taken When the DTC Sets

The following actions may occur:

The EBCM disables the ABS/dynamic rear proportion (DRP).
The ABS indicator turns ON.
The brake warning indicator turns ON.
Conditions for Clearing the DTC

Certain failures that may cause this DTC to set cannot be cleared. Other failures that may cause this DTC to set may be cleared, at least temporarily, by using the scan tool Clear DTCs function.

Diagnostic Aids

Replace the EBCM if this DTC continues to set intermittently.




2. DTC C0550

Circuit Description

At each power-up, the transfer case shift control module runs a self-test on the following:

EEPROM Checksum
ROM Checksum
RAM Checksum
RAM Malfunction
DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC C0550 ECU Malfunction

Conditions for Running the DTC

The ignition is ON.
System voltage is 9-18 volts.
Conditions for Setting the DTC

Critical operational parameters stored in EEPROM have failed Checksum test indicating invalid data.
Masked ROM code has failed Checksum test indicating that masked ROM data is no longer valid.
ROM code has failed Checksum test indicating that ROM data is no longer valid.
One or more ROM locations have failed operational test indicating that some portions of RAM are not functional.
Action Taken When the DTC Sets

The SERVICE AWD indicator remains illuminated for the remainder of the current ignition cycle.
The transfer case control switch does not display the current position LED while DTC C0550 is current.
Conditions for Clearing the DTC

Replace the transfer case shift control module.
Perform the Diagnostic System Check - Vehicle.
Test Description

The numbers below refer to the step numbers on the diagnostic table.
This step has the technician attempt to reprogram the transfer case shift control module.
This step has the technician replace and reprogram the transfer case shift control module.


3.DTC C0550

Circuit Description

At each power-up, the transfer case shift control module runs a self-test on the following functions:

EEPROM Checksum
ROM Checksum
RAM Checksum
RAM Malfunction
DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC C0550 ECU Malfunction

Conditions for Running the DTC

The ignition is ON.
System voltage is 9-18 volts.
Conditions for Setting the DTC

Critical operational parameters stored in EEPROM have failed Checksum test, indicating invalid data.
Masked ROM code has failed Checksum test, indicating that masked ROM data is not currently valid.
ROM code has failed Checksum test, indicating that ROM data is not currently valid.
One or more ROM locations have failed operational test, indicating that some portions of RAM are not functional.
Action Taken When the DTC Sets

The SERVICE 4WD indicator remains illuminated for the remainder of the current ignition cycle.
The transfer case control switch does not display the current position LED while DTC C0550 is current.
Conditions for Clearing the DTC

Replace the transfer case shift control module.
Perform the Diagnostic System Check - Vehicle.
Test Description

The numbers below refer to the step numbers on the diagnostic table.
This step has the technician attempt to reprogram the transfer case shift control module.
This step has the technician replace and reprogram the transfer case shift control module.
Записан

biker78

  • Полковник
  • *
  • Оффлайн Оффлайн
  • Возраст: 48
  • Пол: Мужской
  • Сообщений: 1219
  • Автомобиль: Hummer H2 `08
  • Имя: Сергей
  • Местоположение: Димитровград
  • Карма: +60/-2

Ваще чудеса.
Прозвонил всю проводку к задним датчикам скорости, и от мозгов и от блока управления трансмиссией, и между мозгами и блоком АБС - все ОК.
Махнул датчики местами. Если бы какой то сдох, то ошибка бы стала другая, не по АБС, а по трансмиссии. Знгачит с ними тоже все ОК.
Взял с разборки другой блок АБС - вылезла ошибка по датчику АБС переднего правого колеса, а моя ошибка пропала. :) Этот новый блок вернул.
Взял с другой разборки блок АБС - вроде все пропало, но спустя 1 час езды (20 км :) ) СНОВА ПОЯВИЛАСЬ.
ЧТО ЗА ХРЕНЬ???
Проводка к датчикам в норме, датчики в норме, блок АБС другой - а ошибку показывает C0055/
Оказалось плохой контакт + на блоке АБС. Поэтому блок АБС переглючивало и он показывал ошибку по датчику скорости. На разъеме все ок - потеря где-то в районе бензобака. Провод идет под заднее сиденье, так что париться не стали - кинули под капот на предохранитель. Все ОК теперь.
Записан

Military

  • Ст. Лейтенант
  • *
  • Оффлайн Оффлайн
  • Возраст: 53
  • Пол: Мужской
  • Сообщений: 606
  • Автомобиль: Trailblazer 2006г.
  • Имя: Юрий
  • military69
  • Местоположение: Мурманск
  • Карма: +30/-0

Помогите, кто может!
Практически сразу после покупки вылез чек.
Ошибки 411 и 171.
Промыли форсунки
и сказали, что необходима замена топливного фильтра!?
Приехал домой покопался в нете и понял что его на моем авто нет :o, точнее есть но он не обслуживаемый.М енять бензонасос по такому заключению совсем не хочется. Съездил в Норвегию к друзьям, поездил там на 95, другого у них нет. Чек пропал сам!!! Вернулся залил родной 92 через 200км выскочил снова. Ошибки те же, но  увеличился сильно расход топлива, особенно на холостом ходу!:(  Нормального сервиса в Мурманске нет даже у официалов! Что делать не знаю!
Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0

DTC P0411

Diagnostic Instructions

Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
Strategy Based Diagnosis for an overview of the diagnostic approach.
Diagnostic Procedure Instructions provide an overview of each diagnostic category.
DTC Descriptor

DTC P0411
Secondary Air Injection (AIR) System Incorrect Air Flow Detected
Circuit/System Description

The secondary air injection (AIR) system aids in the reduction of hydrocarbon emissions during a cold start. The system forces fresh filtered air into the exhaust stream in order to accelerate the catalyst operation. An electric air pump, the secondary AIR injection pump, provides filtered air on demand to the AIR control solenoid valve/pressure sensor assembly. The AIR control solenoid valve/pressure sensor assembly controls the flow of air from the AIR pump to the exhaust manifold. The AIR valve relay supplies the current needed to operate the AIR control solenoid valve/pressure sensor assembly. A pressure sensor is used to monitor the air flow from the AIR pump. The powertrain control module (PCM) supplies the internal pressure sensor with a 5-volt reference, an electrical ground, and a signal circuit.

The AIR diagnostic uses 3 phases to test the AIR system:

DTCs P0411 and P2430 run during Phase 1.
DTCs P2430 and P2440 run during Phase 2.
DTC P2444 runs during Phase 3.
During phase 1, both the AIR pump and the solenoid valve are activated. Normal secondary air function occurs. Expected system pressure is 8-10 kPa above barometric pressure (BARO).

During phase 2, only the AIR pump is activated. The solenoid valve is closed. Pressure sensor performance and solenoid valve deactivation are tested. Expected system pressure is 20-25 kPa above BARO.

During phase 3, neither the AIR pump nor the solenoid valve is activated. AIR pump deactivation is tested. Expected system pressure equals BARO.

In all 3 phases, testing is accomplished by comparing the measured pressure against the expected pressure. The PCM can detect faults in the AIR pump, AIR control solenoid valve/pressure sensor assembly, and the exhaust check valve. The pressure sensor can also detect leaks and restrictions in the secondary AIR system plumbing.

Conditions for Running the DTC

DTC P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0125, P0128, P0201, P0202, P0203, P0204, P0300, P0412, P0418, P0420, P0606, P1106, P1107, P1111, P1112, P1114, P1115, P1635, P1639, P2430, P2431, P2432, P2433
More than 60 minutes has elapsed since the last cold start.
The system voltage is 9-18 volts .
The BARO parameter is more than 70 kPa .
The MAF sensor parameter is less than 33 g/s .
The AIR system is commanded ON.
The conditions are stable for more than 5 seconds .
DTC P0411 runs once per trip start up when the above conditions are met and AIR pump operation is requested.
Conditions for Setting the DTC

The difference between the predicted system pressure and the actual system pressure is more than 6 kPa .
DTC P0411 sets within 22 seconds when the above condition is met.
Action Taken When the DTC Sets

DTC P0411 is a type B DTC.

Conditions for Clearing the MIL/DTC

DTC P0411 is a type B DTC.

Circuit/System Verification

If any other AIR DTCs are set, perform those diagnostics first.
Engine running, observe that the AIR Pressure Sensor parameter approximately equals BARO.
Engine running, enable the AIR pump with a scan tool and observe that the AIR Pressure Sensor parameter equals approximately 20-25 kPa above BARO .
Engine running, enable the AIR solenoid with a scan tool and observe that the AIR Pressure Sensor parameter equals approximately 8-10 kPa above BARO.
Circuit/System Testing

Important: You must perform the Circuit/System Verification before proceeding with Circuit/System Testing.

Ignition ON, observe that the AIR pump is not activated.
¤   If the AIR pump is activated, test the AIR pump voltage supply circuit for a short to voltage. If the circuit tests normal, test the AIR pump relay control circuit for a short to ground. If the circuits test normal, test the AIR pump relay. If the relay and circuits test normal, replace the PCM.
Ignition ON, enable the AIR pump with a scan tool and observe that the AIR pump is activated.
¤   If the AIR pump is not activated, test the AIR pump voltage supply and ground circuits for more than 2 ohms of resistance. If the circuits test normal, test both AIR pump relay voltage supply circuits for an open/high resistance or a short to ground. If the circuits test normal, test the AIR pump relay control circuit for an open/high resistance or a short to voltage. If the circuits test normal, test the AIR pump relay. If the relay and circuits test normal, test the AIR pump. If the relay, pump, and circuits test normal, replace the PCM.
Disconnect the AIR solenoid.
Connect a test lamp between the AIR solenoid voltage supply circuit terminal 6 and ground circuit terminal 4.
Ignition ON, observe that the test lamp is not illuminated.
¤   If the test lamp is illuminated, test the AIR solenoid valve voltage supply circuit for a short to voltage. If the circuit tests normal, test the AIR solenoid valve relay control circuit for a short to ground. If the circuits test normal, test the AIR solenoid valve relay. If the relay and circuits test normal, replace the PCM.
Enable the AIR solenoid with a scan tool and observe that the test lamp is illuminated.
¤   If the test lamp is not illuminated, test the AIR solenoid voltage supply circuit and both AIR solenoid relay voltage supply circuits for an open/high resistance or a short to ground. If the circuits test normal, test the AIR solenoid ground circuit for an open/high resistance. If the circuits test normal, test both AIR solenoid relay control circuits for and open/high resistance or a short to voltage. If the circuits test normal, test the AIR solenoid relay. If the relay and circuits test normal, replace the PCM.
Connect all electrical connectors.
Engine RUNNING, enable the AIR solenoid valve with a scan tool and observe that the AIR Pressure Sensor parameter equals approximately 8-10 kPa above BARO.
¤   If not within the specified range, continue with this procedure.
Remove the AIR inlet hose from the AIR pump.
Engine RUNNING, enable the AIR solenoid valve with a scan tool and observe that the AIR Pressure Sensor parameter increases to 8-10 kPa above BARO.
¤   If within the specified range, the AIR pump inlet hoses/pipes are restricted. Remove the restriction or replace the hose/pipe.
¤   If not within the specified range, continue with this procedure.
Disconnect the hose from the AIR pump outlet.
Disconnect the hose quick-connect from the AIR solenoid valve inlet.
Install a length of standard 1 inch I.D. (25.4 mm) hose from the AIR pump outlet to the AIR solenoid valve inlet.
Engine RUNNING, enable the AIR solenoid valve with a scan tool and observe that the AIR Pressure Sensor parameter increases to 8-10 kPa above BARO.
¤   If within the specified range, the AIR pump outlet hoses/pipes are restricted or leaking. Remove the restriction or replace the hose/pipe.
¤   If less than the specified range, replace the AIR pump.
¤   If more than the specified range, continue with this procedure.
Remove the AIR solenoid valve.
Leave the standard hose and harness connector connected.
Engine RUNNING, enable the AIR solenoid valve with a scan tool and observe that the AIR Pressure Sensor parameter increases to approximately 7 kPa above BARO.
¤   If more than the specified range, replace the AIR solenoid valve.
¤   If within the specified range, test/inspect the cylinder head for restriction.
Component Testing

Relay Test
Test between the normally-closed switch terminals, if any, for 0 ohms .
Test between the normally-open switch terminals for infinite ohms.
Test between each switch terminal and either coil terminal for infinite ohms.
Connect the relay coil terminals to ground and fused power to energize the relay.
Test between each switch terminal and each coil terminal for 0 volts .
Test between the normally-closed switch terminals, if any, for infinite ohms.
Test between the normally-open switch terminals for 0 ohms .
Pump

Connect the AIR pump to fused battery voltage and ground and observe pressurized airflow at the pump outlet.

If pressurized airflow is not observed, replace the pump.

Solenoid Valve

Apply fused battery voltage and ground to the solenoid and verify that the valve opens and closes completely as voltage is applied to and removed from the solenoid. Observe that the valve is not obstructed or leaking.

If the valve operates incorrectly, leaks, or is obstructed, remove the obstruction or replace the valve.

Repair Instructions

Secondary Air Injection Pump Replacement
Secondary Air Injection Solenoid Valve Replacement
Secondary Air Injection Pump Hose Replacement
Control Module References for control module replacement and programming See: Testing and Inspection\Programming and Relearning
Repair Verification

With the ignition ON and the engine OFF, observe that the AIR pump is not operating.
With the engine running, enable the AIR solenoid with a scan tool and observe that the AIR Pressure Sensor parameter equals approximately 8-10 kPa above BARO.
With the engine running, enable the AIR pump with a scan tool and observe that the AIR Pressure Sensor parameter equals approximately 20-25 kPa above BARO.
Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0

DTC P0171

Circuit Description

The powertrain control module (PCM) controls the air/fuel metering system in order to provide the best possible combination of driveability, fuel economy and emission control. Fuel delivery is controlled differently during Open Loop and Closed Loop. During Open Loop, the PCM determines fuel delivery based on sensor signals, without heated oxygen sensor (HO2S) input. During Closed Loop the PCM adds HO2S inputs and level of purge to calculate short and long term fuel trim adjustments. If the HO2S indicates a lean condition, the fuel trim values will be above 0 percent . If the HO2S indicates a rich condition, the fuel trim values will be less than 0 percent . The short term fuel trim values change rapidly in response to the HO2S voltage signals. The long term fuel trim makes coarse adjustments in order to maintain an air/fuel ratio of 14.7:1. A block of cells contain information arranged in combinations of engine RPM and engine load for a full range of vehicle operating conditions. The long term fuel trim diagnostic is based on an average of cells currently being used. The PCM selects the cells based on the engine speed and load. If the PCM detects an excessively lean condition, DTC P0171 sets.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0171 Fuel Trim System Lean

Conditions for Running the DTC

DTCs P0013, P0014, P0017, P0030, P0036, P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0128, P0130, P0131, P0132, P0133, P0134, P0135, P0136, P0137, P0138, P0140, P0141, P0201-P0206, P0220, P0222, P0223, P0230, P0300, P0326, P0327, P0332, P0411, P0412, P0418, P0442, P0443, P0446, P0449, P0451, P0452, P0453, P0454, P0455, P0496, P0502, P0503, P0506, P0507, P060D, P060E, P1101, P1133, P1134, P1380, P1381, P1516, P1681, P2101, P2119, P2120, P2122, P2123, P2125, P2127, P2128, P2135, P2138, P2176, P2430, P2431, P2432, P2433, P2440, P2444 are not set.
The engine is in Closed Loop status.
The engine coolant temperature (ECT) is between -7 and +120°C (+19.4 and +248°F) .
The intake air temperature is between -7 and +145°C (+19.4 and +293°F) .
The manifold absolute pressure (MAP) is between 15-100 kPa (2.2-14.5 psi) .
The mass air flow (MAF) is between 1-512 g/s .
The vehicle speed is less than 132 km/h (82 mph) .
The engine speed is between 400-6,100 RPM .
The barometric pressure is more than 72 kPa (10.4 psi) .
The fuel level is more than 10 percent .
DTC P0171 runs continuously when the above conditions are met.
Conditions for Setting the DTC

The long term fuel trim weighted average value is more than a calibrated value.
The above condition is present for 2 seconds .
Action Taken When the DTC Sets

The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.
Conditions for Clearing the MIL/DTC

The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
Clear the MIL and the DTC with a scan tool.
Diagnostic Aids

Test for fuel contamination. Small amounts of water can be delivered to the fuel injectors and cause a lean exhaust indication. A lean exhaust indication can also be caused by too much alcohol in the fuel.
The system will go lean if an injector is not supplying enough fuel.
A lean condition could be present during high fuel demand due to a fuel pump that does not pump enough fuel.
Review the Failure Records with a scan tool. If an intermittent condition is suspected, refer to Intermittent Conditions. See: Initial Inspection and Diagnostic Overview\Intermittent Conditions

Записан