Российский Клуб Chevrolet TrailBlazer & Chevrolet Tahoe

Автор Тема: КОДЫ ОШИБОК OBD 2 ===расшифровка и решение проблем===  (Прочитано 382940 раз)

0 Пользователей и 2 Гостей просматривают эту тему.

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0

DTC P0014

Circuit Description

The cam phasing system is a hydraulically actuated phase shifting mechanism. The powertrain control module (PCM) supplies the ignition positive driver and ground circuits. A pulse width modulated (PWM) driver controls the amount that the camshaft actuator solenoid assembly advances or retards the exhaust camshaft. The exhaust camshaft is commanded to a maximum retard position of 25 degrees . When the exhaust camshaft is retarded at the maximum rate, the duty cycle of the signal is at 100 percent . The maximum advance rate has a 0 percent duty cycle. Other than when the camshaft is at full advance, a 50 percent duty cycle is used to maintain a steady retard angle.

If the desired and actual cam phase angle error exceeds its tolerance value for a certain amount of time, then DTC P0014 will set.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0014 Exhaust Camshaft Position (CMP) System Performance

Conditions for Running the DTC

The engine is running.
The PCM has enabled the cam phaser.
DTC P0014 runs continuously when the above conditions are met.
Conditions for Setting the DTC

The vehicle must be driven.
The difference between the desired CAM phase angle and the actual CAM phase angle is more than 3.5 degrees .
The CAM phaser is steady for 12.25 seconds .
The condition is present for 12.25 seconds .
Action Taken When the DTC Sets

The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.
Conditions for Clearing the MIL/DTC

The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
Clear the MIL and the DTC with a scan tool.
Diagnostic Aids

The scan tool cam phase control function increments the cam phaser in 10 percent increments. Each increment equates to 2.5 degrees of cam phasing. A cam phase angle of 15 degrees is achieved by commanding the phaser with the scan tool to 60 percent .
Inspect any engine mechanical work that has been performed recently. Verify that the engine timing has not been altered.
If this DTC is set along with any crankshaft position (CKP) or camshaft position (CMP) sensor DTCs, then both the CKP and CMP sensor DTCs should be diagnosed prior to performing this diagnostic. The PCM uses both inputs to determine the actual camshaft position.
Check the following items:
A loose CMP sensor causing a variance in the sensor signal
A loose CKP sensor causing a variance in the sensor signal
Excessive free play in the timing chain and gear assembly
Debris or contamination interfering with the camshaft position actuator solenoid valve assembly
Debris or contamination interfering with the camshaft position actuator assembly
Engine oil has a major impact upon the camshaft actuation systems responsiveness. Oil temperature, viscosity, and quality can slow and/or inhibit the phaser's ability to reach a desired phase angle.
Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0

TC P0496

System Description


   
This DTC tests for undesired intake manifold vacuum flow to the evaporative emission (EVAP) system. The control module seals the EVAP system by commanding the EVAP canister purge solenoid valve Closed and the EVAP canister vent solenoid valve Closed. The control module monitors the fuel tank pressure (FTP) sensor to determine if a vacuum is being drawn on the EVAP system. If vacuum in the EVAP system is more than a predetermined value within a predetermined time, this DTC sets.

The following table illustrates the relationship between the ON and OFF states, and the Open or Closed states of the EVAP canister purge and vent solenoid valves.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0496 Evaporative Emissions (EVAP) System Flow During Non-Purge

Conditions for Running the DTC

DTCs P0068, P0106, P0107, P0108, P0112, P0113, P0117, P0118, P0120, P0122, P0123, P0125, P0128, P0130, P0131, P0132, P0133, P0134, P0135, P0220, P0442, P0443, P0446, P0449, P0452, P0453, P0455, P0502, P0503, P0601, P0602, P0604, P0606, P060D, P060E, P0641, P1133, P1516, P1621, P2101, P2120, P2125, P2135, P2138, P2176 are not set.
The ignition voltage is between 11-18 volts .
The barometric pressure (BARO) is more than 74 kPa .
The throttle position (TP) is between 7-35 percent .
The fuel level is between 15-85 percent .
The start-up engine coolant temperature (ECT) is between 4-30°C (39-86°F) .
The start-up intake air temperature (IAT) is between 4-30±C (39°-86°F) .
The start-up ECT and IAT are within 8°C (14.4°F) of each other.
The vehicle speed sensor (VSS) is less than 137 km/h (85 mph) .
DTC P0496 runs once per trip when the above conditions are met.
Conditions for Setting the DTC

The control module detects excessive vacuum during a non-purge condition within a 1-minute test.

Action Taken When the DTC Sets

The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.
Conditions for Clearing the MIL/DTC

The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
Clear the MIL and the DTC with a scan tool.
Diagnostic Aids

An intermittent condition could be caused by an improperly installed or damaged EVAP canister purge valve or a temporary blockage in the EVAP canister purge solenoid valve.
For intermittent conditions, refer to Intermittent Conditions
Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0

DTC P0014
Circuit Description
The cam phasing system is a hydraulically actuated phase shifting mechanism. The powertrain control module (PCM) supplies the ignition positive driver and ground circuits. A pulse width modulated (PWM) driver controls the amount that the camshaft actuator solenoid assembly advances or retards the exhaust camshaft. The exhaust camshaft is commanded to a maximum retard position of 25 degrees. When the exhaust camshaft is retarded at the maximum rate, the duty cycle of the signal is at 100 percent. The maximum advance rate has a 0 percent duty cycle. Other than when the camshaft is at full advance, a 50 percent duty cycle is used to maintain a steady retard angle.

If the desired and actual cam phase angle error exceeds its tolerance value for a certain amount of time, then DTC P0014 will set.

DTC Descriptor
This diagnostic procedure supports the following DTC:

DTC P0014 Exhaust Camshaft Position (CMP) System Performance

Conditions for Running the DTC
    •  The engine is running.

    •  The PCM has enabled the cam phaser.

    •  DTC P0014 runs continuously when the above conditions are met.

Conditions for Setting the DTC
    •  The vehicle must be driven.

    •  The difference between the desired CAM phase angle and the actual CAM phase angle is more than 3.5 degrees.

    •  The CAM phaser is steady for 12.25 seconds.

    •  The condition is present for 12.25 seconds.

Action Taken When the DTC Sets
    •  The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.

    •  The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.

Conditions for Clearing the MIL/DTC
    •  The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.

    •  A current DTC, Last Test Failed, clears when the diagnostic runs and passes.

    •  A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.

    •  Clear the MIL and the DTC with a scan tool.

Diagnostic Aids
    •  The scan tool cam phase control function increments the cam phaser in 10 percent increments. Each increment equates to 2.5 degrees of cam phasing. A cam phase angle of 15 degrees is achieved by commanding the phaser with the scan tool to 60 percent.

    •  Inspect any engine mechanical work that has been performed recently. Verify that the engine timing has not been altered.

    •  If this DTC is set along with any crankshaft position (CKP) or camshaft position (CMP) sensor DTCs, then both the CKP and CMP sensor DTCs should be diagnosed prior to performing this diagnostic. The PCM uses both inputs to determine the actual camshaft position.

    •  Check the following items:

       -  A loose CMP sensor causing a variance in the sensor signal

       -  A loose CKP sensor causing a variance in the sensor signal

       -  Excessive free play in the timing chain and gear assembly

       -  Debris or contamination interfering with the camshaft position actuator solenoid valve assembly

       -  Debris or contamination interfering with the camshaft position actuator assembly

    •  Engine oil has a major impact upon the camshaft actuation systems responsiveness. Oil temperature, viscosity, and quality can slow and/or inhibit the phaser's ability to reach a desired phase angle.

    •  If an intermittent condition exists, refer to Intermittent Conditions .

Step
 Action
 Values
 Yes
 No
 
Schematic Reference: Engine Controls Schematics

Connector End View Reference: Powertrain Control Module Connector End Views or Engine Controls Connector End Views
 
1
 Did you perform the Diagnostic System Check - Vehicle?
 --
 Go to Step 2
 Go to Diagnostic System Check - Vehicle
 
2
 Connect a scan tool.
Start and idle the engine for 2 minutes.
Increase engine RPM to 1,500.
With a scan tool, command the cam phase solenoid from 0-100 percent.
Does the Cam Phase Angle Actual remain close to the Cam Phase Angle Desired at all commanded positions?
 --
 Go to Step 3
 Go to Step 4
 
3
 Observe the Freeze Frame/Failure Records data for this DTC.
Turn OFF the ignition for 30 seconds.
Start the engine.
Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Does the DTC fail this ignition?
 --
 Go to Step 4
 Go to Diagnostic Aids
 
4
 Let the engine idle.

Does the engine run rough or stall?
 --
 Go to Step 9
 Go to Step 5
 
5
 Turn OFF the ignition.
Let the vehicle sit for 1 minute.
Check the engine oil level.
Is the engine oil level within operating range?
 --
 Go to Step 6
 Go to Fluid and Lubricant Recommendations
 
6
 Install an oil pressure gage. Refer to Oil Pressure Diagnosis and Testing .
Start the engine.
Increase the engine RPM to 1,400 RPM.
Observe the engine oil pressure.
Does the oil pressure gage indicate engine oil pressure less than the specified value?
 193 kPa (28 psi)
 Go to Oil Pressure Diagnosis and Testing
 Go to Step 7
 
7
 Increase engine RPM to 1,500 RPM.
With a scan tool, command the cam phase solenoid from 0-100 percent.
Does the Cam Phase Angle Actual increment at all?
 --
 Go to Step 8
 Go to Step 10
 
8
 Turn OFF the ignition.
Disconnect the camshaft position (CMP) actuator solenoid connector.
Measure the resistance of the CMP actuator solenoid valve assembly with a DMM. Refer to Circuit Testing .
Does the resistance measure within the specified value?
 8-12 ohms
 Go to Step 13
 Go to Step 20
 
9
 Turn OFF the ignition.
Disconnect the CMP actuator solenoid connector.
Probe the CMP actuator solenoid high control circuit with a test lamp connected to good ground. Refer to Probing Electrical Connectors .
Caution: Avoid contact with moving parts and hot surfaces while working around a running engine in order to prevent physical injury.

Start the engine.
With a scan tool, command the cam phase solenoid between 0-50 percent.
Does the test lamp turn ON and OFF?
 --
 Go to Step 10
 Go to Step 15
 
10
 Turn OFF the ignition.
Remove the CMP solenoid valve assembly from the engine block. Refer to Camshaft Position Actuator Solenoid Valve Replacement .
Inspect the camshaft position actuator solenoid valve assembly for the following:
•  Torn screens

•  Debris on the screens

•  Debris clogging the oil ports

•  Missing screens

•  Oil seepage at the solenoid connector pins

Did you find a problem?
 --
 Go to Step 20
 Go to Step 11
 
11
 Connect a jumper wire between the CMP actuator low reference circuit at the solenoid and to a good ground.
Connect a fused jumper wire between B+ and the CMP actuator high control circuit at the solenoid and to battery voltage. Refer to Using Fused Jumper Wires .
Momentarily touch the fused jumper to B+.
Observe the spool valve inside the CMP actuator.
Does the spool valve move from fully closed to fully opened?
 --
 Go to Step 12
 Go to Step 18
 
12
 Inspect for the following conditions:

    •  Excessive timing chain play--Refer to Camshaft Timing Chain, Sprocket, and Tensioner Replacement .

    •  Excessive camshaft end play

    •  Excessive crankshaft end play

    •  Proper installation of the CMP actuator assembly--Refer to Camshaft Timing Chain, Sprocket, and Tensioner Replacement .

Did you find and correct the condition?
 --
 Go to Step 22
 Go to Step 13
 
13
 Disconnect the powertrain control module (PCM). Refer to Control Module References for replacement, setup, and programming.
Measure the resistance on the CMP actuator high control circuit with a DMM. Refer to Circuit Testing .
Does the resistance measure more than the specified value?
 5 ohms
 Go to Step 16
 Go to Step 14
 
14
 Measure the resistance on the low reference circuit with a DMM. Refer to Circuit Testing .

Does the resistance measure more than the specified value?
 5 ohms
 Go to Step 17
 Go to Camshaft Position Actuator Diagnosis
 
15
 Test the CMP actuator high control circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?
 --
 Go to Step 22
 Go to Step 19
 
16
 Repair the high resistance on the CMP actuator high control circuit. Refer to Wiring Repairs .

Did you complete the repair?
 --
 Go to Step 22
 --
 
17
 Repair the high resistance on the CMP actuator low reference circuit. Refer to Wiring Repairs .

Did you complete the repair?
 --
 Go to Step 22
 --
 
18
 Test for an intermittent and for a poor connection at the CMP actuator solenoid valve assembly. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?
 --
 Go to Step 22
 Go to Step 20
 
19
 Test for an intermittent and for a poor connection at the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?
 --
 Go to Step 22
 Go to Step 21
 
20
 Replace the CMP actuator solenoid. Refer to Camshaft Position Actuator Solenoid Valve Replacement .

Did you complete the replacement?
 --
 Go to Step 22
 --
 
21
 Replace the PCM. Refer to Control Module References for replacement, setup, and programming.

Did you complete the replacement?
 --
 Go to Step 22
 --
 
22
 Clear the DTCs with a scan tool.
Turn OFF the ignition for 30 seconds.
Start the engine.
Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?
 --
 Go to Step 2
 Go to Step 23
 
23
 Observe the Capture Info with a scan tool.

Are there any DTCs that have not been diagnosed?
 --
 Go to Diagnostic Trouble Code (DTC) List - Vehicle
 System OK
 
Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0

#03-06-04-030F: Various Driveability Symptoms Due to Clogged Fuel Injectors, MIL/SES DTCs P0171, P0172, P0174, P0300, P1174, P1175 (Clean Fuel Injectors and/or Perform Injector Test With AFIT - CH-47976) - (Dec 10, 2007)

 
Subject: Various Driveability Symptoms Due to Clogged Fuel Injectors, MIL/SES DTCs P0171, P0172, P0174, P0300, P1174, P1175 (Clean Fuel Injectors and/or Perform Injector Test With AFIT - CH-47976)


Models: 2000-2008 GM Passenger Cars and Light Duty Trucks (Including Saturn)

 2003-2008 HUMMER H2

 2006-2008 HUMMER H3

 2005-2008 Saab 9-7X

 with 2.0L, 2.2L, 2.4L, 2.8L, 3.1L, 3.4L, 3.5L, 3.8L, 3.9L, 4.2L, 4.3L, 4.8L, 5.3L, 6.0L, 6.2L or 8.1L Engine (VINs X, F, D, 4, 5, T, 8, J, E, H, L, 6, K, 1, 2, R, W, S, X, V, T, M, N, U, H, Y, 8, G -- RPOs LNF, L61, LN2, L43, LD9, LK5, LG8, LA1, LX5, LX9, LZ4, LZE, L52, L36, L67, L26, LZ9, LZ8, LGD, LL8, LU3, LR4, LM7, LH6, LQ9, LQ4, LS2, L76, L92, L18)

 and MULTEC® 2 Fuel Injectors




--------------------------------------------------------------------------------

This bulletin is being revised to update the model year to 2008. Please discard Corporate Bulletin Number 03-06-04-030E (Section 06 -- Engine/Propulsion System).


--------------------------------------------------------------------------------

Condition
Some customers may comment on any of the following various driveability symptoms:

    •  Extended Crank Time

    •  Hard to Start

    •  MIL/SES Illuminated with DTCs

    •  Hesitation

    •  Lack of Power

    •  Surge or Chuggle

    •  Rough Idle

    •  Light or Intermittent Misfire

Cause
Due to various factors, the fuel injectors may become restricted. Extensive testing has demonstrated that fuel related issues are the cause of clogged injectors. At this point, no specific fuel, fuel constituent, or engine condition has been identified as causing the restriction. The restriction causes the engine to operate at a lean air fuel ratio. This may either trigger the MIL to illuminate or the engine to develop various driveability symptoms.

Correction
Fuel injector restrictions, deposits can be cleaned on the vehicle using the following procedure. Under NO circumstances should this procedure be modified, changed or shortened. As a long term solution, and to prevent reoccurrence, customers should be encouraged to use Top Tier Detergent Gasoline . For further information on Top Tier detergent gasoline and fuel retailers, please refer to the following Corporate Bulletin Numbers:

    •  04-06-04-047G (U.S. Only)

    •  05-06-04-022D (Canada ONLY)

Notice: GM UPPER ENGINE AND FUEL INJECTOR CLEANER is the only injector cleaning agent approved for use with General Motors fuel system components. Other injector cleaners may cause damage to plastics, plated metals or bearings. General Motors has completed extensive laboratory testing of GM Upper Engine and Fuel Injector Cleaner, and can assure its compatibility with General Motors fuel system components, as long as the cleaning procedure is followed correctly.

Injector Cleaning Procedure
The following tools, or their equivalent, are required:

    •  CH-47976 Active Fuel Injector Tester (AFIT)

    •  J 35800-A Fuel Injector Cleaner 

    •  J 37287 Fuel Line Shut-off Adapter 

    •  J 42964 Fuel Line Shut-off Adapter 

    •  J 42873 Fuel Line Shut-off Adapter 

    •  * One bottle of GM Upper Engine and Fuel Injector Cleaner, P/N 88861802 (in Canada, P/N 88861804) 

    •  * One bottle of GM Fuel System Treatment Plus, P/N 88861011 (in Canada, P/N 88861012)

Active Fuel Injector Tester (AFIT- CH-47976)
Some dealers may not have an Active Fuel Injector Tester (AFIT- CH-47976). Dealers can contact 1-800-GM-TOOLS (1-800-468-6657) to order an AFIT- CH-47976. Dealers still can test the fuel injectors without an AFIT. Refer to Fuel Injector Diagnosis (w/ J 39021 or Tech 2®) in SI.

Important: As mentioned in the AFIT User Guide, vehicles that are not listed in the AFIT menu can still be tested with the AFIT. Depending on the model, it may be possible to enter the previous model year and proceed with testing using the DLC connection. If this is not possible on the model that you are working on, it will be necessary to use the direct connection method outlined in the AFIT User Guide (See Pages 17-31).

General Motors recommends that the Active Fuel Injector Tester (AFIT) be used in testing fuel injectors. If the SI diagnostics do not isolate a cause for this concern, use the Active Fuel Injector Tester (AFIT - CH-47976) to perform an "Injector Test" as outlined in the AFIT User Guide.

The AFIT "Injector Test" measures the flow characteristics of all fuel injectors, which is more precise when compared with the standard Tech 2® fuel injector balance test. As a result, the AFIT is more likely to isolate the cause of a P1174 DTC (for example: if it is being caused by a fuel injector concern).

The CH-47976 (Active Fuel Injector Tester - AFIT) can also be used to measure fuel pressure and fuel system leak down. Also, as mentioned in the P1174 SI diagnosis, if the misfire current counters or misfire graph indicate any misfires, it may be an indicator of the cylinder that is causing the concern. Refer to Fuel Injector Diagnosis (w/CH-47976) in SI for additional instructions.

Training (U.S.)
To access the training video on AFIT, take the following path at the GM Training Website:

After logging into the gmtraining.com website, choose the link on the left side of the page titled "web video library."
Then choose "technical."
Next, within the search box, type in September course number "10206.09D.
This will bring up a link with this course. Scroll through to choose "feature topic."
At this point, the seminar can be chosen to view or the video related to the AFIT.
Additional training is available from the gmtraining.com website. Please see TECHassist 16044.18T2 Active Fuel Injector Tester and also see 16044.14D1 GM Powertrain Performance for more information on GM Upper Engine and Fuel Injector Cleaner.

Also, dealers can now download software updates for the AFIT at GM Dealer Equipment (GMDE) on the web at http://www.gmde.net/AFIT.cfm.

Training (Canada)
To access the training video on AFIT, take the following path at the GMPro LMS Training Website:

After logging into the <www.gmprocanada .com> website, choose the link on the left side of the page titled "Catalog."
Then choose "Catalog Search."
Next, within the search box, Select Course Number - Contains - "T" then select search.
This will bring up a list of TECHassist courses. Scroll through to choose "Active Fuel Injector Tester" and select "View."
At this point, a new window will open and the program can be Launched.
Also, dealers can now download software updates for the AFIT at GM Dealer Equipment (GMDE) on the web at http://www.gmde.net/softwareupdates/.

Techlink
Additional information can be found on AFIT (June 2006 Edition) and GM Upper Engine and Fuel Injector Cleaner (November 2006 Edition) in Techlink. To access the articles, take the following path:

Go to GM DealerWorld (U.S.) or the GM infoNET (Canada).
Click on the Service Tab in DealerWorld (GM infoNET for Canada).
Click on the GM Techlink Hyperlink.
Click on the Archives Hyperlink at GM Techlink.
•  Click on 06-2006 in the Archives Section and Click on the Active Fuel Injector Tester Link in the June 2006 Techlink Article. 

•  Click on 11-2006 in the Archives Section and Click on the GM Top Engine Cleaner Replaced Link in the November 2006 Techlink Article.

Injector Cleaning Procedure
Notice: GM UPPER ENGINE AND FUEL INJECTOR CLEANER is the only injector cleaning agent recommended. DO NOT USE OTHER CLEANING AGENTS AS THEY MAY CONTAIN METHANOL, WHICH CAN DAMAGE FUEL SYSTEM COMPONENTS. Under NO circumstances should the GM Upper Engine and Fuel Injector Cleaner be added to the vehicle fuel tank.

Do not exceed the recommended cleaning solution concentration. Testing has demonstrated that exceeding the recommended cleaning solution concentration does not improve the effectiveness of this procedure.


Important: Vehicles with less than 160 km (100 mi) on the odometer should not have the injectors cleaned. These vehicles should have any out of specification injectors replaced.

For 4, 5 and 6 cylinder engines, empty two of the 30 ml (1 oz) reservoirs of the GM Upper Engine and Fuel Injector Cleaner container into the J 35800-A - Injector Cleaning Tank then add 420 ml (14 oz) of regular unleaded gasoline. If you are using any other brand of cleaning tank, you will need a total of 60 ml (2 oz) mixed with 420 ml (14 oz) of regular unleaded gasoline.
For 8 cylinder engines, empty two of the 30 ml (1 oz) reservoirs of the GM Upper Engine and Fuel Injector Cleaner container into the J 35800-A - Injector Cleaning Tank then add 420 ml (14 oz) of regular unleaded gasoline. If you are using any other brand of cleaning tank, you will need a total of 60 ml (2 oz) of Upper Engine and Fuel Injector Cleaner mixed with 420 ml (14 oz) of regular unleaded gasoline. This procedure will need to be repeated for a second time for an 8 cylinder engine (8 cylinder engines receive 960 ml total fluid - 120 ml (4 oz) of Upper Engine and Fuel Injector Cleaner and 840 ml (28 oz) of gasoline.
Be sure to follow all additional instructions provided with the tool.
Electrically disable the vehicle fuel pump by either removing the fuel pump fuse or the fuel pump relay and disconnecting the oil pressure switch connector, if equipped.
Turn the ignition to the OFF position.
Relieve fuel pressure and disconnect the fuel feed and return lines at the fuel rail. Plug the fuel feed and return lines coming off the fuel rail with J 37287, J 42873 or J 42964 as appropriate for the fuel system.
Connect the J 35800-A to the vehicle fuel rail.
Pressurize the J 35800-A to 510 kPa (75 psi).
Start and idle the engine until it stalls, due to lack of fuel. This should take approximately 15-20 minutes.
Turn the ignition to the OFF position.
Disconnect the J 35800-A from the fuel rail.
Reconnect the vehicle fuel pump relay and oil pressure switch connector, if equipped.
Remove the J 37287, J 42873 or J 42964 and reconnect the vehicle fuel feed and return lines.
Start and idle the vehicle for an additional two minutes to ensure residual injector cleaner is flushed from the fuel rail and fuel lines.
Pour the entire contents of GM Fuel System Treatment Plus (P/N 88861011 [in Canada, P/N 88861012]) into the tank and advise the customer to fill the tank.
Review the benefits of using Top Tier Detergent gasoline with the customer and recommend that they add a bottle of GM Fuel System Treatment Plus to the fuel tank at every oil change. Regular use of GM Fuel System Treatment Plus should keep the customer from having to repeat the injector cleaning procedure.
Road test the vehicle to verify that the customer concern has been corrected.
Parts Information
Part Number
 Description
 Qty
 
88861802
 GM Upper Engine and Fuel Injector Cleaner 473 ml (16 oz) Container (U.S.)
 1*
 
88861804
 GM Upper Engine and Fuel Injector Cleaner 473 ml Container (Canada)
 1
 
88861011
 Fuel System Treatment Plus 591 ml (20 oz) Container (U.S.)
 1
 
88861012
 Fuel System Treatment Plus 591 ml Container (Canada)
 1
 

* Only 1/8 of the cost may be claimed for 4 and 6 cylinder engines and 1/4 of the cost for 8 cylinder engines.

Warranty Information (excluding Saab U.S. Models)
For vehicles repaired under warranty, use:

Labor Operation
 Description
 Labor Time
 
*J5645
 Cleaning Injector:
 
 
4 Cylinder Engine
 0.8 hr
 
5 Cylinder Engine
 0.7 hr
 
6 Cylinder Engine
 0.7 hr
 
8 Cylinder Engine
 0.9 hr
 
**Add:
 Diagnostic Time
 0.0-0.3 hr
 
* This labor operation number is for bulletin use only. This number will not be published in the Labor Time Guide.

**A total diagnostic time equal to the time allowed for cleaning, J5645, may be claimed for performing the injector diagnosis procedure.
 

Warranty Information (Saab U.S. Models)
For vehicles repaired under warranty, use:

Labor Operation
 Description
 Failed Object
 Fault/Reason Code
 Location Code
 Warranty Type
 Repair/Action Code
 Labor Time
 
2421101
 Injector, Replace Engine Code S
 24211
 71
 0
 01
 01
 Use Published Labor Operation Time
 
2421102
 Injector, Replace Engine Code M
 24211
 71
 0
 01
 01
 Use Published Labor Operation Time
 
Add

1002001
 Diagnostic Time
 --
 --
 --
 --
 --
 Use Published Labor Operation Time
 
2421105
 Cleaning Injector, 6 Cylinder Engine
 24211
 71
 0
 01
 05
 0.7 hr*
 
2421106
 Cleaning Injector, 8 Cylinder Engine
 24211
 71
 0
 01
 05
 0.9 hr*
 

 
Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0

DTC P0411
Diagnostic Instructions
    •  Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

    •  Review Strategy Based Diagnosis for an overview of the diagnostic approach.

    •  Diagnostic Procedure Instructions provide an overview of each diagnostic category.

DTC Descriptor
DTC P0411 : Secondary Air Injection (AIR) System Incorrect Air Flow Detected


Diagnostic Fault Information
Circuit
 Short to Ground
 Open/High Resistance
 Short to Voltage
 Signal Performance
 
Pressure Sensor 5-Volt Reference Voltage
 P2432
 P2431
 P2431
 P2430, P2431
 
Pressure Sensor Signal
 P2432
 P2432
 P2433
 P2430, P2431
 
Pressure Sensor Low Reference
 --
 P2433
 --
 --
 
Pump Voltage Supply
 P0411
 P0411
 P2444
 --
 
Pump Ground
 --
 P0411
 --
 --
 
Solenoid Voltage Supply
 P0411
 P0411
 P2440
 --
 
Solenoid Ground
 --
 P0411
 --
 --
 
Pump Relay Coil Voltage Supply
 P0411, P0418
 P0411, P0418
 --
 --
 
Pump Relay Coil Control
 P0418 P2444
 P0411, P0418
 P0418
 --
 
Pump Relay Switch Supply
 P0411
 P0411
 --
 --
 
Solenoid Relay Coil Voltage Supply
 P0411, P0412
 P0411, P0412
 --
 --
 
Solenoid Relay Coil Control
 P0412, P2440
 P0411, P0412
 P0412
 --
 
Solenoid Relay Switch Supply
 P0411
 P0411
 --
 --
 

Typical Scan Tool Data
AIR Pressure Sensor Circuit
 Normal Range
 Short to Ground
 Open
 Short to Voltage
 
Operating Conditions: Key ON, Engine OFF
 
5-Volt Reference Voltage
 BARO
 41 kPa
 41 kPa
 111 kPa
 
Pressure Sensor Signal
 BARO
 42 kPa
 41 kPa
 150 kPa
 
Low Reference
 BARO
 BARO
 145 kPa
 BARO
 

Circuit/System Description
The secondary air injection (AIR) system aids in the reduction of hydrocarbon emissions during a cold start. The system forces fresh filtered air into the exhaust stream in order to accelerate the catalyst operation. An electric air pump, the secondary AIR injection pump, provides filtered air on demand to the AIR control solenoid valve/pressure sensor assembly. The AIR control solenoid valve/pressure sensor assembly controls the flow of air from the AIR pump to the exhaust manifold. The AIR valve relay supplies the current needed to operate the AIR control solenoid valve/pressure sensor assembly. A pressure sensor is used to monitor the air flow from the AIR pump. The powertrain control module (PCM) supplies the internal pressure sensor with a 5-volt reference, an electrical ground, and a signal circuit.

The AIR diagnostic uses 3 phases to test the AIR system:

DTCs P0411 and P2430 run during Phase 1.
DTCs P2430 and P2440 run during Phase 2.
DTC P2444 runs during Phase 3.
During phase 1, both the AIR pump and the solenoid valve are activated. Normal secondary air function occurs. Expected system pressure is 8-10 kPa above barometric pressure (BARO).

During phase 2, only the AIR pump is activated. The solenoid valve is closed. Pressure sensor performance and solenoid valve deactivation are tested. Expected system pressure is 20-25 kPa above BARO.

During phase 3, neither the AIR pump nor the solenoid valve is activated. AIR pump deactivation is tested. Expected system pressure equals BARO.

In all 3 phases, testing is accomplished by comparing the measured pressure against the expected pressure. The PCM can detect faults in the AIR pump, AIR control solenoid valve/pressure sensor assembly, and the exhaust check valve. The pressure sensor can also detect leaks and restrictions in the secondary AIR system plumbing.

Conditions for Running the DTC
    •  DTC P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0125, P0128, P0201, P0202, P0203, P0204, P0300, P0412, P0418, P0420, P0606, P1106, P1107, P1111, P1112, P1114, P1115, P1635, P1639, P2430, P2431, P2432, P2433

    •  More than 60 minutes has elapsed since the last cold start.

    •  The system voltage is 9-18 volts.

    •  The BARO parameter is more than 70 kPa.

    •  The MAF sensor parameter is less than 33 g/s.

    •  The AIR system is commanded ON.

    •  The conditions are stable for more than 5 seconds.

    •  DTC P0411 runs once per trip start up when the above conditions are met and AIR pump operation is requested.

Conditions for Setting the DTC
    •  The difference between the predicted system pressure and the actual system pressure is more than 6 kPa.

    •  DTC P0411 sets within 22 seconds when the above condition is met.

Action Taken When the DTC Sets
DTC P0411 is a type B DTC.

Conditions for Clearing the MIL/DTC
DTC P0411 is a type B DTC.

Reference Information
Schematic Reference
Engine Controls Schematics

Connector End View Reference

    •  Powertrain Control Module Connector End Views

    •  Engine Controls Connector End Views


Electrical Information Reference

    •  Circuit Testing

    •  Connector Repairs

    •  Testing for Intermittent Conditions and Poor Connections

    •  Wiring Repairs

    •  Electrical Center Identification Views


Scan Tool Reference

    •  Scan Tool Data List

    •  Scan Tool Data Definitions

    •  Scan Tool Output Controls


Special Tools
J 36169-HD Heavy Duty Fused Jumper

Circuit/System Verification
Verify that DTCs P0412, P0418, P2430, P2431, P2432, P2433, P2440, or P2444 are not set.
⇒ If any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle.

Ignition ON, command the AIR pump relay ON and OFF with a scan tool. The air pump should turn ON and OFF
⇒ If the air pump does not turn ON or OFF, refer to Secondary Air injection Pump Malfunction.

Command the AIR solenoid relay ON and OFF with a scan tool. The AIR solenoid valve should click with each command.
⇒ If the AIR solenoid valve does operate as specified, refer to Secondary Air Injection Solenoid Valve Malfunction.

Engine running, command the AIR pump relay ON with a scan tool while observing the AIR Pressure Sensor parameter. The reading should be 20-25 kPa above the BARO reading.
⇒ If less than the specified range, refer to Secondary Air Injection System Pressure Low.

⇒ If greater than the specified range, refer to Secondary Air Injection System Pressure High.

Engine running, command the AIR solenoid relay ON while observing the AIR Pressure Sensor parameter. The reading should be 8-10 kPa above BARO.
⇒ If less than the specified range, refer to Secondary Air Injection System Pressure Low.

⇒ If greater than the specified range, refer to Secondary Air Injection System Pressure High.

Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
Secondary Air Injection Pump Malfunction
Ignition OFF, disconnect the AIR pump relay.
Ignition ON, verify that a test lamp does not illuminate between the controlled output circuit terminal 87 and ground.
⇒ If the test lamp illuminates, test the controlled output circuit for a short to voltage.

Verify that a test lamp illuminates between the AIR pump relay coil ignition circuit terminal 86 and ground.
⇒ If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal and the ignition circuit fuse is open, replace the AIR pump relay.

Verify that a test lamp illuminates between the AIR pump relay switch B+ circuit terminal 30 and ground.
⇒ If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit tests normal and the B+ circuit fuse is open, test the controlled output circuit for a short to ground.

Ignition OFF, disconnect the harness connector at the AIR pump.
Test for less than 2 ohms between the AIR pump ground circuit terminal B and ground.
⇒ If greater than the specified range, test the ground circuit for an open/high resistance.

Connect the harness connector at the AIR pump.
. Connect the J 36169-HD with a 60A fuse between the AIR pump relay switch B+ circuit terminal 30 and the controlled output circuit terminal 87. Verify the AIR pump is activated.
⇒ If the AIR pump does not activate, test the controlled output circuit for an open/high resistance. If the circuit tests normal, test or replace the AIR pump.

Remove the J 36169-HD .
Connect a test lamp between the AIR pump relay coil ignition circuit terminal 86 and the AIR pump relay control circuit terminal 85.
. Ignition ON, command the AIR pump relay ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
⇒ If the test lamp is always ON, test the AIR pump relay control circuit for a short to ground. If the circuit tests normal, replace the ECM.

⇒ If the test lamp is always OFF, test the AIR pump relay control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the ECM.

If all circuits test normal, replace the air pump relay.
Secondary Air Injection Solenoid Malfunction
Ignition OFF, disconnect the AIR solenoid relay.
Ignition ON, verify that a test lamp does not illuminate between the controlled output circuit terminal and ground.
⇒ If the test lamp illuminates, test the controlled output circuit for a short to voltage.

Verify that a test lamp illuminates between the AIR solenoid relay coil ignition circuit terminal and ground.
⇒ If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.

Verify that a test lamp illuminates between the AIR solenoid relay switch B+ circuit terminal and ground.
⇒ If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit tests normal and the B+ circuit fuse is open, test the controlled output circuit for a short to ground.

Ignition OFF, disconnect the harness connector at the AIR solenoid valve.
Test for less than 2 ohms between the AIR solenoid ground circuit terminal 4 and ground.
⇒ If greater than the specified range, test the ground circuit for an open/high resistance.

Connect the harness connector at the AIR solenoid valve.
Connect a 15A fused jumper wire between the AIR solenoid relay switch B+ circuit terminal and the controlled output circuit terminal. Verify the AIR solenoid valve activates.
⇒ If the AIR solenoid valve does not activate, test the controlled output circuit for an open/high resistance. If the circuit tests normal, test or replace the AIR solenoid valve.

Remove the 15A fused jumper wire.
Connect a test lamp between the AIR solenoid relay coil ignition circuit terminal and the relay coil control circuit terminal.
Ignition ON, command the AIR solenoid relay ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
⇒ If the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the ECM.

⇒ If the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the ECM.

If all circuits test normal, replace the AIR solenoid relay.
Secondary Air Injection System Pressure Low
Engine running, inspect for exhaust leaks between the AIR solenoid valve and the catalytic converter.
⇒ If an exhaust leak is detected, repair as necessary.

Ignition OFF, disconnect the AIR pump relay.
Engine running, connect the J 36169-HD with a 60A fuse between the AIR pump relay switch B+ circuit terminal 30 and the controlled output circuit terminal 87. Verify the AIR Pressure Sensor parameter is not 20-25 kPa above BARO.
⇒ If 20-25 kPa above BARO, replace the AIR pump relay.

Ignition OFF, remove the fused jumper wire and connect the AIR pump relay.
Remove the air inlet hose at the AIR pump.
Engine running, command the AIR solenoid relay ON while observing the AIR Pressure Sensor parameter. Verify the reading is not 8-10 kPa above BARO.
⇒ If 8-10 kPa above BARO, the AIR pump inlet hoses/pipes are restricted. Remove the restriction or replace the inlet hose/pipe.

Ignition OFF, disconnect the hose at the AIR pump outlet.
Disconnect the hose at the AIR solenoid valve inlet.
Install a length of standard 1 inch I.D. (25.4 mm) hose from the AIR pump outlet to the AIR solenoid valve inlet.
Engine running, command the AIR solenoid ON while observing the AIR Pressure Sensor parameter. Verify the reading is not 8-10 kPa above BARO.
⇒ If 8-10 kPa above BARO, test/inspect the AIR pump outlet hoses/pipes for leaks or restrictions.

Test all AIR pump wiring and connections for less than 2 ohms. If the wiring and connections test normal, replace the AIR pump.
Secondary Air Injection System Pressure High
Ignition OFF, remove the AIR solenoid valve.
Connect the AIR pump outlet pipe/hose to the AIR solenoid valve.
Connect the AIR solenoid harness at the AIR solenoid valve.
Engine running, command the AIR solenoid relay ON while observing the AIR Pressure Sensor parameter. The reading should be less than 11 kPa above BARO.
⇒ If greater than the specified value, replace the AIR solenoid valve.

Inspect the AIR solenoid valve gaskets for proper alignment. If normal, test/inspect the cylinder head or exhaust manifold for a restriction.
Component Testing
Relay Test
Test between the normally-closed switch terminals, if any, for 0 ohms.
Test between the normally-open switch terminals for infinite ohms.
Test between each switch terminal and either coil terminal for infinite ohms.
Connect the relay coil terminals to ground and fused power to energize the relay.
Test between each switch terminal and each coil terminal for 0 volts.
Test between the normally-closed switch terminals, if any, for infinite ohms.
Test between the normally-open switch terminals for 0 ohms.
Pump
Connect the AIR pump to fused battery voltage and ground and observe pressurized airflow at the pump outlet.

⇒ If pressurized airflow is not observed, replace the pump.

Solenoid Valve
Apply fused battery voltage and ground to the solenoid and verify that the valve opens and closes completely as voltage is applied to and removed from the solenoid. Observe that the valve is not obstructed or leaking.

⇒ If the valve operates incorrectly, leaks, or is obstructed, remove the obstruction or replace the valve.

Repair Instructions
    •  Secondary Air Injection Pump Replacement

    •  Secondary Air Injection Solenoid Valve Replacement

    •  Secondary Air Injection Pump Hose Replacement

    •  Control Module References for control module replacement and programming

Repair Verification
With the ignition ON and the engine OFF, observe that the AIR pump is not operating.
With the engine running, enable the AIR solenoid with a scan tool and observe that the AIR Pressure Sensor parameter equals approximately 8-10 kPa above BARO.
With the engine running, enable the AIR pump with a scan tool and observe that the AIR Pressure Sensor parameter equals approximately 20-25 kPa above BARO.
Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0

DTC P0496
System Description
This DTC tests for undesired intake manifold vacuum flow to the evaporative emission (EVAP) system. The control module seals the EVAP system by commanding the EVAP canister purge solenoid valve Closed and the EVAP canister vent solenoid valve Closed. The control module monitors the fuel tank pressure (FTP) sensor to determine if a vacuum is being drawn on the EVAP system. If vacuum in the EVAP system is more than a predetermined value within a predetermined time, this DTC sets.

The following table illustrates the relationship between the ON and OFF states, and the Open or Closed states of the EVAP canister purge and vent solenoid valves.

Control Module Command
 EVAP Canister Purge Solenoid Valve
 EVAP Canister Vent Solenoid Valve
 
ON
 Open
 Closed
 
OFF
 Closed
 Open
 

DTC Descriptor
This diagnostic procedure supports the following DTC:

DTC P0496 Evaporative Emissions (EVAP) System Flow During Non-Purge

Conditions for Running the DTC
    •  DTCs P0068, P0106, P0107, P0108, P0112, P0113, P0117, P0118, P0120, P0122, P0123, P0125, P0128, P0130, P0131, P0132, P0133, P0134, P0135, P0220, P0442, P0443, P0446, P0449, P0452, P0453, P0455, P0502, P0503, P0601, P0602, P0604, P0606, P060D, P060E, P0641, P1133, P1516, P1621, P2101, P2120, P2125, P2135, P2138, P2176 are not set.

    •  The ignition voltage is between 11-18 volts.

    •  The barometric pressure (BARO) is more than 74 kPa.

    •  The throttle position (TP) is between 7-35 percent.

    •  The fuel level is between 15-85 percent.

    •  The start-up engine coolant temperature (ECT) is between 4-30°C (39-86°F).

    •  The start-up intake air temperature (IAT) is between 4-30°C (39°-86°F).

    •  The start-up ECT and IAT are within 8°C (14.4°F) of each other.

    •  The vehicle speed sensor (VSS) is less than 137 km/h (85 mph).

    •  DTC P0496 runs once per trip when the above conditions are met.

Conditions for Setting the DTC
The control module detects excessive vacuum during a non-purge condition within a 1-minute test.

Action Taken When the DTC Sets
    •  The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.

    •  The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.

Conditions for Clearing the MIL/DTC
    •  The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.

    •  A current DTC, Last Test Failed, clears when the diagnostic runs and passes.

    •  A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.

    •  Clear the MIL and the DTC with a scan tool.

Diagnostic Aids
    •  An intermittent condition could be caused by an improperly installed or damaged EVAP canister purge valve or a temporary blockage in the EVAP canister purge solenoid valve.

    •  For intermittent conditions, refer to Intermittent Conditions .

Test Description
The numbers below refer to the step numbers on the diagnostic table.

This step inspects for a leaking EVAP canister purge solenoid valve.

Removing the fuel fill cap will equalize the pressure inside the tank with atmospheric pressure. At 0 inches of H2O the FTP sensor should be near 1.5 volts. If the sensor is not, there is a concern with the sensor or related wiring.

Step
 Action
 Values
 Yes
 No
 
Schematic Reference: Evaporative Emissions Hose Routing Diagram and Engine Controls Schematics

Connector End View Reference: Powertrain Control Module Connector End Views or Engine Controls Connector End Views
 
1
 Did you perform the Diagnostic System Check - Vehicle?
 --
 Go to Step 2
 Go to Diagnostic System Check - Vehicle
 
2
 Disconnect the purge pipe from the evaporative emission (EVAP) canister purge solenoid valve.
Install a hand held vacuum gage to the EVAP canister purge solenoid valve purge port.
Disconnect the EVAP canister purge solenoid valve harness connector.
Monitor vacuum on the vacuum gage.
Start the engine and allow the engine to idle.
Increase the idle to 1,200-1,500 RPM.
Does the vacuum gage indicate an increase in vacuum?
 --
 Go to Step 8
 Go to Step 3
 
3
 Connect the EVAP canister purge solenoid valve harness connector.
Monitor vacuum on the vacuum gage.
Increase the idle to 1,200-1,500 RPM.
Does the vacuum gage indicate an increase in vacuum?
 --
 Go to Step 5
 Go to Step 4
 
4
 Turn OFF the ignition.
Remove and then install the fuel fill cap.
Turn ON the ignition, with the engine OFF.
Observe the Fuel Tank Pressure Sensor parameter with a scan tool.
Is the Fuel Tank Pressure Sensor parameter within the specified value?
 -0.5 to +0.5 in H2O
 Go to Diagnostic Aids
 Go to Step 6
 
5
 Test the control circuit of the EVAP canister purge solenoid valve for a short to ground. Refer to Testing for Short to Ground and Wiring Repairs.

Did you find and correct the conditions?
 --
 Go to Step 9
 Go to Step 8
 
6
 Test for an intermittent and for a poor connection at the fuel tank pressure (FTP) sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs.

Did you find and correct the condition?
 --
 Go to Step 9
 Go to Step 7
 
7
 Replace the FTP sensor. Refer to Fuel Tank Pressure Sensor Replacement .

Did you complete the replacement?
 --
 Go to Step 9
 --
 
8
 Replace the EVAP canister purge solenoid valve. Refer to Evaporative Emission Canister Purge Solenoid Valve Replacement .

Did you complete the replacement?
 --
 Go to Step 9
 --
 
9
 Clear the DTCs with a scan tool.
Turn OFF the ignition for 30 seconds.
Start the engine.
Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?
 --
 Go to Step 2
 Go to Step 10
 
10
 Observe the Capture Info with a scan tool.

Are there any DTCs that have not been diagnosed?
 --
 Go to Diagnostic Trouble Code (DTC) List - Vehicle
 System OK
 
Записан

nalim83

  • Сержант
  • *
  • Оффлайн Оффлайн
  • Пол: Мужской
  • Сообщений: 92
  • Автомобиль: Cadillac Escalade 2011
  • Местоположение: Москва
  • Карма: +6/-0

Вылезла ошибка P0171 (обедненная смесь банк 1),и как следствие повышенные обороты двигла(900 об./мин.), когда отключаю первую лямбду обороты приходят в норму.Решил ее (лямбду) заменить, но после этого вылезла ошибка P0172 (обогащенная смесь банк 1) и обороты опять в районе 900. :o...но без лямбды работает нормально...Мож ет кто что подскажет?
Записан

SlavaR

  • Капитан
  • *
  • Оффлайн Оффлайн
  • Возраст: 54
  • Пол: Мужской
  • Сообщений: 697
  • Автомобиль: TB 2006
  • Местоположение: Екатеринбург
  • Карма: +42/-1

Подскажите, что за ошибка?
Записан

MiniOn

  • Ст. Прапорщик
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 271
  • Местоположение: Самара, Тольятти
  • Карма: +10/-4

Вчера был на диагностике обнаружили ошибки:
Р0141 - цепь нагревателя датчика кислорода
Р0304 - пропуск в 4-м цилиндре. это и так было видно. буду смотреть свечи и катушку.
Р0171 - Бедная смесь.

Вместо катализатора стоит пламегаситель с выведенным в сторону 2-м датчиком кислорода. Так же установленно газовое оборудование.
Машина работает на повышенных оборотах при ХХ. примерно 900-1000 об.
Официалы предлагают менять бензонасос, что на мой взгляд кажется глупостью, т.к. при работе на газу те же симптомы что и при работе на бензине.

Подскажите куда смотреть и как можно забороть этого джекичана?
Записан

МоНстриК

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Пол: Мужской
  • Сообщений: 3549
  • Автомобиль: ТБ. 2005 LTZ
  • Имя: Михаил
  • Местоположение: г.Щелково М.о
  • Карма: +228/-13

Подскажите, что за ошибка?
такойже програмкой выдал ошибки С 0035, С 0040 , С 0055, неисправность цепи датчика скорости левого переднего колеса, правого, неисправность цепи заднего датчика скорости, это что за хрень??????
Записан

kopa

  • Рядовой
  • *
  • Оффлайн Оффлайн
  • Пол: Мужской
  • Сообщений: 1
  • Автомобиль: Chevrolet TrailBlazer 2002
  • Местоположение: Владивосток
  • Карма: +0/-0

Добрый день уважаемые форумчане, может кто сталкивался с  P0014, P1221, P1345, P1516, последних три ошибки из истории, постоянно горит чек, иногда срабатывает падения мощности. Дроссель чистый, катушки рабочие,  свечи в порядке, расход 19л по городу, после ночной стоянке при прогреве двигателя,  троит и глохнет. Да еще недавно менял цепь!!! Что это за хрень и как с этим бороться ?   
Записан

Military

  • Ст. Лейтенант
  • *
  • Оффлайн Оффлайн
  • Возраст: 53
  • Пол: Мужской
  • Сообщений: 606
  • Автомобиль: Trailblazer 2006г.
  • Имя: Юрий
  • military69
  • Местоположение: Мурманск
  • Карма: +30/-0

Всем привет!По форуму пролазил ,но ответа не нашел!У кого-нибудь кроме меня еще вылазила ошибка 452(низкое давление в системе утилизации паров)И как с этим бороться!На сервисе предложили снять бак и заменить датчик на бензонасосе, но что то пока не хочется. Тем более на сто процентов они не уверены!Поведение машины не изменилось ,но чувствую стала поджирать топливо,не глобально на литр максимум!
Записан

ag001

  • Рядовой
  • *
  • Оффлайн Оффлайн
  • Возраст: 40
  • Пол: Мужской
  • Сообщений: 2
  • Местоположение: Москва
  • Карма: +0/-0

С периодичностью появляется ошибка Р0014 и сама исчезает на след день.
Что это?? как с этим жить ))) )))  ???


P0014 - ошибка системы изменения фаз. Загорается когда дельта между фактическим и заданным положением распредвала составляет более 3.5 градусов. Возможно неисправен или периодически зависает клапан изменения фаз, а может ратянута цепь или датчик положения распредвала периодически выдает неверные данные, а может глюк PCM или что-то еще - нужна более тщательная диагностика.
...авто стояла 2 недели, после запуска появилась такая же ошибка Р0014, подскажите номера з\ч, кто уже с этой ошибкой сталкивался, плиз..
Пару дней назад вылезла ошибка P0014 перерыл весь интернет и форум.... готовился к худшему :'(  вкратце: появилась, сбросил, поездил вечер :) а с утра опять появилась :o при чем единственное чем отличалось поведение машины - это при переключении с паркинга на скорость поднимались а потом опускались обороты. Вылечил до смеха ;D просто посмотрел количество масла в движке и оказалось :o меньше нижней рески, долил 1 литр масла все через 2 минуты исчезло :D.
Записан

policeman

  • Рядовой
  • *
  • Оффлайн Оффлайн
  • Возраст: 48
  • Пол: Мужской
  • Сообщений: 1
  • Автомобиль: '07 Escalade ESV
  • Местоположение: Москва ЗАО
  • Карма: +0/-0

Специалисты, проконсультируй те)))) Ошибка P0011
Кадиллак Эскалейд 07 год.
Проявилась при длительном движении по трассе при следующих обстоятельствах:
Примерно через 30 мин постоянного равномерного движения выскочила ошибка по Стабилитраку (трэкшн контроль), он отключился. Через 5 минут сам включился, лампа погасла. Через примерно 30 минут все повторилось. А на третий раз все повторилось, но одновременно с лампой джеки чан (P0011).
Р0011 Положение распределительн ого вала А - повышенное опережение ( ряд цилиндров1 )
P0011 "A" Camshaft Position - Timing Over-Advanced or System Performance

Не пойму, как увязать ошибку стабилитрака с этой ошибкой.
Записан
'07 Cadillac Escalade ESV
'92 Volvo 240 V8 powered by Lexus LS400

Медвед Полоскун

  • Рядовой
  • *
  • Оффлайн Оффлайн
  • Пол: Мужской
  • Сообщений: 5
  • Автомобиль: Hummer H3 Base
  • Местоположение: Санкт-Петербург, Веселый Поселок
  • Карма: +0/-0

Всем кто остался не безучастным к моей проблеме_СПАСИБ О!
Разобрался!Сто процентный правильный совет дал GooLYVER!
Оказалось, причина в разгерметизации воздушной системы и некорректной работе первой лямды. Вылечили просто. Патрубок надели на место, новую лямду заказал, но и на старой пока проблем не возникает и чек не горит.Разобрали сь и нормально посмотрели только на четвертом сервисе.:(
Жалко что нормальных сервисов совсем мало,а официалы гнут цены и плюс левые причины выдумывают.:(

А что конкретно случилось и как лечили?
У меня похожие симптомы.
Машина Hummer H3
Записан

ultra174

  • Лейтенант
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 413
  • Имя: Вадим
  • Местоположение: Тамбовская область
  • Карма: +20/-2

Всем привет!По форуму пролазил ,но ответа не нашел!У кого-нибудь кроме меня еще вылазила ошибка 452(низкое давление в системе утилизации паров)И как с этим бороться!На сервисе предложили снять бак и заменить датчик на бензонасосе, но что то пока не хочется. Тем более на сто процентов они не уверены!Поведение машины не изменилось ,но чувствую стала поджирать топливо,не глобально на литр максимум!
крышка бака плотно закрывается?
Цитировать (выделенное)
такойже програмкой выдал ошибки С 0035, С 0040 , С 0055, неисправность цепи датчика скорости левого переднего колеса, правого, неисправность цепи заднего датчика скорости, это что за хрень???
 
помоему это прога глючит. У меня то же самое всегда показывает) Хотя точно знаю, что все исправно
Записан

Север

  • Рядовой
  • *
  • Оффлайн Оффлайн
  • Пол: Мужской
  • Сообщений: 3
  • Автомобиль: Chevrolet TrailBlazer
  • Местоположение: Россия, МО
  • Карма: +0/-0

Мужики! Спасите-помогите!!!
ТБ 03. Ехал, никого не трогал, вдруг двигатель сдох.
Сканер выдал Р0116.
Незначительные подтёки по трубке ОЖ внутрь салона.
Движок не заводиться. Антифриз долил, ошибку стёр.
Что делать.
Записан

SlavaR

  • Капитан
  • *
  • Оффлайн Оффлайн
  • Возраст: 54
  • Пол: Мужской
  • Сообщений: 697
  • Автомобиль: TB 2006
  • Местоположение: Екатеринбург
  • Карма: +42/-1

Это ошибка датчика температуры ОЖ.
Записан

Север

  • Рядовой
  • *
  • Оффлайн Оффлайн
  • Пол: Мужской
  • Сообщений: 3
  • Автомобиль: Chevrolet TrailBlazer
  • Местоположение: Россия, МО
  • Карма: +0/-0

И что мне теперь делать, помогите.
Записан

Север

  • Рядовой
  • *
  • Оффлайн Оффлайн
  • Пол: Мужской
  • Сообщений: 3
  • Автомобиль: Chevrolet TrailBlazer
  • Местоположение: Россия, МО
  • Карма: +0/-0

Проверил датчик ОЖ-живой, бензонасос-живой, предохранители, реле-живые!!!
При попытке запуска, загорается панель, высвечивается ошибка (не читается сканером, правда китайским Memo Ckanom).
Стартер крутит, движок молчит.
Ничего не понимаю!!!
Предохранитель 20А №10 болтался в гнезде, закрепил - тоже самое кино.
Помогите советом.
Живу около Кубинки, дер. Чапаевка, до ближайшего известного сервиса - как до Луны пешком.
Записан

МоНстриК

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Пол: Мужской
  • Сообщений: 3549
  • Автомобиль: ТБ. 2005 LTZ
  • Имя: Михаил
  • Местоположение: г.Щелково М.о
  • Карма: +228/-13

ребята подскажите ошибки Р0017 и Р0106 это МАР сенсор???
и номерок его ??????????????????
Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0

TC P0017

Circuit Description

The powertrain control module (PCM) uses the crankshaft position (CKP) sensor and the camshaft position (CMP) sensor information to monitor the correlation between the crankshaft and camshaft positions. If the deviation between the crankshaft and CMP exceeds a calibrated amount, DTC P0017 will set.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0017 Crankshaft Position (CKP) Exhaust - Camshaft Position (CMP) Correlation

Conditions for Running the DTC

The engine is running.
The CMP actuator is commanded to zero for 16 seconds .
DTC P0017 runs continuously when the above conditions are met.
Conditions for Setting the DTC

The deviation between the crankshaft and the camshaft positions exceeds a calibrated amount.
The above condition is met for 4 seconds .
Action Taken When the DTC Sets

The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.
Conditions for Clearing the MIL/DTC

The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
Clear the MIL and the DTC with a scan tool.
Diagnostic Aids

Important: Scan tool control of the CMP actuator solenoid is inhibited when DTC P0017 sets.

The following conditions may cause this DTC to set:

An improperly torqued crankshaft balancer
A mis-built or mis-timed engine
A loose or missing crankshaft balancer bolt
The CMP actuator solenoid stuck open
The CMP actuator stuck in a position other than 0 degrees
Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0

Есть еще один документ по поводу данной ошибки от GM, на всякий случай проверь VIN

#PIP3940B: Supplement To Bulletin 06-06-01-017C - User Tips For EN48464 - keywords camshaft CKP CMP cover crankshaft cylinder DTC en48464 en-48464 front gear head installation left P0017 PCM position removal - (Apr 10, 2007)

 
Subject: Supplement to Bulletin 06-06-01-017C - User Tips for EN48464


Models: 2004-2007 Buick Rainier

 2002-2007 Chevrolet TrailBlazer

 2004-2007 Chevrolet Colorado

 2002-2007 GMC Envoy

 2004-2007 GMC Canyon

 2002-2004 Oldsmobile Bravada

 2006-2007 HUMMER H3

 2005-2007 Saab 9-7X

 with any of the following engines:

 2.8L (VIN 8 - RPO LK5)

 2.9L (VIN 9 - RPO LLV)

 3.5L (VIN 6 - RPO L52)

 3.7L (VIN E - RPO LLR)

 4.2L (VIN S - RPO LL8)




--------------------------------------------------------------------------------

This PI was Superseded To Include A Revised Condition/Concern Description. Please Discard PIP3940A.


--------------------------------------------------------------------------------

The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI.

Condition/Concern:
Carefully follow the repair instructions outlined in 06-06-01-17C to properly use the Lower Timing Gear Tensioner Holding Tool (EN48464). Failure to properly insert and secure the holding tool as instructed in the bulletin may result in a ratchet out movement of the timing chain tensioner and the need to perform additional repair steps not covered by the warranty repair time.

Recommendation/Instructions:
Following are some tips for proper tool usage:

Thoroughly review 06-06-01-017C before the cylinder head replacement process is started.
Review the June 2006 emerging issues broadcast, which contains a video of that highlights the procedure for a 3.5L L52 5 Cylinder Engine. An archived copy of this seminar can be viewed by visiting www.gmtraining.com. Once you log in with your Training Person ID, you can view the seminar by taking the following path: Click "Web Video Library">> Click "Technical">> Type "wedge tool" in the search box that is on the left side of the screen and click "Search">> Click "Emerging Issues - June 2006">> Scroll down the list of topics found in the pop up viewer and click "New tool EN48468" >> Click "Play" on the pop up viewer to view the broadcast. General Motors employees logged into GM Online may not be able view this video due to a conflict with the GM Online firewall.

Canadian Dealers should refer to their taped copy of the August 2006 TAC TALK IDL broadcast.

Before using the tool, make sure that the tool handle and threaded rod unscrew from the wedge as shown below.
 


If the tool handle unscrews from the threaded rod, leaving the threaded rod screwed into the wedge as shown below, apply thread locker to the threads of the tool handle and screw it onto the threaded rod to prevent it from coming off in the future. This should be done before replacing the cylinder head by following 06-06-01-017C.
 


When inserting the wedge, ensure that it is installed in the correct direction as shown below.
 


Bulletin 06-06-01-017C advises that the wedge should be lightly seated using a couple of very light taps with a small plastic or brass hammer. Although these should be light taps, they should also be solid taps to ensure that the wedge is seated properly.
Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed.



Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0

DTC P0106
Diagnostic Instructions
    •  Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

    •  Review Strategy Based Diagnosis for an overview of the diagnostic approach.

    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor
DTC P0106: Manifold Absolute Pressure (MAP) Sensor Performance


Diagnostic Fault Information
Circuit
 Short to Ground
 High Resistance
 Open
 Short to Voltage
 Signal Performance
 
5-Volt Reference
 P0107, P0222, P0651, P2122
 P0106, P0107
 P0107
 P0106, P0108, P0223, P0651, P2123
 P0106, P0107
 
MAP Sensor Signal
 P0107
 P0106, P0107
 P0107
 P0108
 P0106, P0107, P1101
 
Low Reference
 --
 P0106, P0108
 P0106, P0108
 --
 P0106, P0108
 

Typical Scan Tool Data
MAP Sensor  Circuit
 Normal Range
 Short to Ground
 Open
 Short to Voltage
 
5-Volt Reference
 --
 10 kPa
 10 kPa
 104 kPa
 
MAP Sensor Signal
 12-103 kPa
 10 kPa
 10 kPa
 104 kPa
 
Low Reference
 --
 --
 80-103 kPa
 --
 

Circuit Description
The intake flow rationality diagnostic provides the within-range rationality check for the mass air flow (MAF), manifold absolute pressure (MAP), and the throttle position (TP) sensors. This is an explicit model-based diagnostic containing 4 separate models for the intake system.

    •  The throttle model describes the flow through the throttle body and is used to estimate the MAF through the throttle body as a function of barometric pressure (BARO), TP, intake air temperature (IAT), and estimated MAP. The information derived from this model is the MAF Performance Test.

    •  The first intake manifold model describes the intake manifold and is used to estimate MAP as a function of the MAF into the manifold from the throttle body and the MAF out of the manifold caused by engine pumping. The flow into the manifold from the throttle uses the MAF estimate calculated from the above throttle model. The information derived from this model is the MAP Performance Test 1.

    •  The second intake manifold model is identical to the first intake manifold model except that the MAF sensor measurement is used instead of the throttle model estimate for the throttle air input. The information derived from this model is the MAP Performance Test 2.

    •  The fourth model is created from the combination and additional calculations of the throttle model and the first intake manifold model. The information derived from this model is the TP Performance Test.

The estimates of MAF and MAP obtained from this system of models and calculations are then compared to the actual measured values from the MAF, MAP, and the TP sensors and to each other to determine the appropriate DTC to fail. The following table illustrates the possible failure combinations and the resulting DTC or DTCs.

MAF Performance Test
 MAP Performance Test 1
 MAP Performance Test 2
 TP Performance Test
 DTCs Passed
 DTCs Failed
 
X
 X
 OK
 OK
 P0101, P0106, P0121, P1101
 None
 
OK
 OK
 Fault
 OK
 P0101, P0106, P0121, P1101
 None
 
Fault
 OK
 Fault
 OK
 P0106, P0121, P1101
 P0101
 
OK
 Fault
 Fault
 OK
 P0101, P0121, P1101
 P0106
 
Fault
 Fault
 Fault
 OK
 P0121, P1101
 P0101, P0106
 
X
 X
 OK
 Fault
 P0101, P0106, P1101
 P0121
 
OK
 OK
 Fault
 Fault
 P0101, P0106, P0121, P1101
 None
 
Fault
 OK
 Fault
 Fault
 P0101, P0106, P0121
 P1101
 
X
 Fault
 Fault
 Fault
 P0101, P0106, P0121
 P1101
 

Conditions for Running the DTC
    •  DTCs P0102, P0103, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0128, P0335, P0336 are not set.

    •  The engine speed is between 400-8,192 RPM.

    •  The IAT Sensor parameter is between -7 to +125°C (+19 to 257°F).

    •  The ECT Sensor parameter is between 70-125°C (158-257°F).

    •  This DTC runs continuously within the enabling conditions.

Conditions for Setting the DTC
The powertrain control module (PCM) detects that the MAP sensor pressure is not within range of the calculated pressure that is derived from the system of models for more than 0.5 second.

Action Taken When the DTC Sets
DTC P0106 is a Type B DTC.

Conditions for Clearing the MIL/DTC
DTC P0106 is a Type B DTC.

Diagnostic Aids
    •  A wide open throttle (WOT) acceleration from a stop should cause the MAP sensor parameter on the scan tool to increase rapidly to near the BARO Sensor parameter at the time of the 1-2 shift.

    •  A skewed or stuck engine coolant temperature (ECT) sensor or IAT sensor will cause the calculated models to be inaccurate and may cause this DTC to run when it should not. Refer to Temperature Versus Resistance . 

Circuit/System Verification
Important: Verify that the engine is in good mechanical condition before continuing with this diagnostic.

    •  If DTC P0641 or P0651 are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle . 

    •  Verify the integrity of the entire air induction system by inspecting for the following conditions: 

       -  Any damaged components 

       -  Loose or improper installation 

       -  An air flow restriction

       -  Any vacuum leak

       -  Improperly routed vacuum hoses

       -  In cold climates, inspect for any snow or ice buildup

    •  Verify that restrictions do not exist in the MAP sensor port or vacuum source.

    •  Verify that restrictions do not exist in the exhaust system. Refer to Restricted Exhaust . 

    •  The BARO that is used by the engine control module (ECM) to calculate the air flow models is initially based on the MAP sensor at ignition ON. When the engine is running, the ECM will continually update the BARO value near WOT using the MAP sensor and a calculation. A skewed MAP sensor will cause the BARO value to be inaccurate. Determine the current vehicle testing altitude. Ignition ON, observe the scan tool BARO Sensor parameter. Compare the parameter to the Altitude vs Barometric Pressure table. Refer to Altitude Versus Barometric Pressure .

    •  A skewed MAP sensor will also cause the first and second intake manifold models to disagree with the actual MAP sensor measurements. Use the scan tool and compare the MAP Sensor parameter to a known good vehicle, under various operating conditions.

Circuit/System Testing
Important: All electrical components and accessories must be turned OFF, and allowed to power down.

Ignition OFF, disconnect the MAP harness connector at the MAP sensor.
Ignition OFF, test for less than 5 ohms of resistance between the low reference circuit terminal A and ground.
⇒ If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the PCM.

Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal C and ground.
⇒ If less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the PCM.

⇒ If greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the ECM.

Verify the scan tool MAP Sensor parameter is less than 12 kPa.
⇒ If greater than the specified range, test the signal circuit terminal B for a short to voltage. If the circuit tests normal, replace the PCM.

Install a 3-amp fused jumper wire between the signal circuit terminal B and the 5-volt reference circuit terminal C. Verify the scan tool MAP Sensor parameter is greater than 103 kPa.
⇒ If less than the specified range, test the signal circuit terminal B for a short to ground or an open/high resistance. If the circuit tests normal, replace the PCM.

If all circuits test normal, test the MAP sensor. Refer to Component Testing for instructions.

Component Testing
Important: You must perform the Circuit/System Testing in order to verify the integrity of the MAP sensor circuits before proceeding with the Component Testing.

Ignition ON, remove the MAP sensor.
Install a 3-amp fused jumper wire between the 5-volt reference circuit terminal C and the corresponding terminal of the MAP sensor.
Install a jumper wire between the low reference circuit terminal A of the MAP sensor and ground.
Install a jumper wire at terminal B of the MAP sensor.
Connect a DMM between the jumper wire from terminal B of the MAP sensor and ground.
Install the J 35555 to the MAP sensor vacuum port. Slowly apply vacuum to the sensor while observing the voltage on the DMM. The voltage should vary between 0-5.2 volts, without any spikes or dropouts.
⇒ If the voltage is not within the specified range or is erratic, replace the MAP sensor.






Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0

P0107
 Manifold Absolute Pressure (MAP) Sensor Circuit Low Voltage
 ECM, PCM
     •  DTC P0107 for the 4.2L engine

    •  DTC P0107 or P0108 for the 5.3L engine

    •  DTC P0107 or P0108 for the 6.0L engine 
 
Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0

P0106
 Manifold Absolute Pressure (MAP) Sensor Performance
 ECM, PCM
     •  DTC P0106 for the 4.2L engine

    •  DTC P0106 for the 5.3L engine

    •  DTC P0106 for the 6.0L engine 
 
Записан

МоНстриК

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Пол: Мужской
  • Сообщений: 3549
  • Автомобиль: ТБ. 2005 LTZ
  • Имя: Михаил
  • Местоположение: г.Щелково М.о
  • Карма: +228/-13

о Господи еще бы понять сто значит эта абра-кадабра :o :o
Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0

Войди на форум через Google Chrome, там встроенный переводчик есть и все станет ясно
Записан

МоНстриК

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Пол: Мужской
  • Сообщений: 3549
  • Автомобиль: ТБ. 2005 LTZ
  • Имя: Михаил
  • Местоположение: г.Щелково М.о
  • Карма: +228/-13

да перевел через него вот и думаю что это за набор слов..........
Записан

МоНстриК

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Пол: Мужской
  • Сообщений: 3549
  • Автомобиль: ТБ. 2005 LTZ
  • Имя: Михаил
  • Местоположение: г.Щелково М.о
  • Карма: +228/-13

0106 ошибка это МАР сенсор, а 0017 - это что положение коленвала?
Записан