Российский Клуб Chevrolet TrailBlazer & Chevrolet Tahoe

Автор Тема: Что то странное творится с машиной!!!  (Прочитано 14685 раз)

0 Пользователей и 1 Гость просматривают эту тему.

UralBlazer

  • Мл. сержант
  • *
  • Оффлайн Оффлайн
  • Возраст: 48
  • Пол: Мужской
  • Сообщений: 74
  • Автомобиль: Chevrolet TrailBlazer LTZ
  • Я зла не помню...Я его записываю!
  • Местоположение: Свердловская область
  • Карма: +0/-0

Товарисчи!
Нижайше испрашиваю у всех вас совета и наставления! Чувствую, грядёт горе большое, неведомое. Страшно мне други, что однажды мой "бегемот" откажет мне во взаимности, и останусь я в одиночестве посредь столбовой дороги без надежды на помощь, врагам и злыдням на поругание.... :'(
Короче:
Утро, запускаем двигатель, заводится без проблем. Слышно лёгкое шипение в районе компрессора кондиционера, которое через минуту-другую становится прерывистым, и исчезает вовсе. Затем, появляется лёгкий стук, где то в районе клапанной крышки, такой - Цок-цок-цок..неторопливый такой. Через несколько секунд пропадает....
Но не это главное, когда машина постоит и остынет, загорается "джеки чан", а при трогании с места чувствуется потеря мощности, педаль газа просто проваливается до конца,в надежде сдвинуть махину с места. Машина разгоняется и на скорости уже ведёт себя вполне адекватно, но это до первой остановки на перекрёстке...з атем всё повторяется.
Если не лавать машине остывать машине в течении дня, то при последующих пусках двигателя и езде такого не наблюдается.

Я понимаю что это как то связано с прогевом двигателя и расширением деталей, глюком электроники, .... х.з. с чем ещё.....но как ЭТО исправить я пока не знаю. Ошибку прочитать смогу тока на следующей неделе....

Поможите, люди добрые!
Записан
Лучше умереть и чувствовать себя спокойно, чем жить и волноваться!

sirotka72

  • Капитан
  • *
  • Оффлайн Оффлайн
  • Возраст: 53
  • Пол: Мужской
  • Сообщений: 670
  • Автомобиль: ТБ 1 LTZ 2007 РЕСТАЙЛ КАЛИНИНГРАД
  • Не с нашим счастьем...
  • Местоположение: ...где-то на окраине вселеной...(Тобольск)
  • Карма: +11/-0
Re: Что то странное творится с машиной!!!
« Ответ #1 : 12 июня 2011, 18:02:42 »

почитай темы про дроссельную заслонку.где то было что она сдыхает похожим образом
Записан
Не откладывай на завтра то, что можно отложить на послезавтра...

UralBlazer

  • Мл. сержант
  • *
  • Оффлайн Оффлайн
  • Возраст: 48
  • Пол: Мужской
  • Сообщений: 74
  • Автомобиль: Chevrolet TrailBlazer LTZ
  • Я зла не помню...Я его записываю!
  • Местоположение: Свердловская область
  • Карма: +0/-0
Re: Что то странное творится с машиной!!!
« Ответ #2 : 12 июня 2011, 18:14:50 »

Читал, и даже смотрел.
К сожелению совсем недвано масло поменял, а то бы помыл для профилактики. Но тем не менее..она в лёгком сером налёте и ничего криминального не заметил на ней.
Записан
Лучше умереть и чувствовать себя спокойно, чем жить и волноваться!

sirotka72

  • Капитан
  • *
  • Оффлайн Оффлайн
  • Возраст: 53
  • Пол: Мужской
  • Сообщений: 670
  • Автомобиль: ТБ 1 LTZ 2007 РЕСТАЙЛ КАЛИНИНГРАД
  • Не с нашим счастьем...
  • Местоположение: ...где-то на окраине вселеной...(Тобольск)
  • Карма: +11/-0
Записан
Не откладывай на завтра то, что можно отложить на послезавтра...

UralBlazer

  • Мл. сержант
  • *
  • Оффлайн Оффлайн
  • Возраст: 48
  • Пол: Мужской
  • Сообщений: 74
  • Автомобиль: Chevrolet TrailBlazer LTZ
  • Я зла не помню...Я его записываю!
  • Местоположение: Свердловская область
  • Карма: +0/-0
Re: Что то странное творится с машиной!!!
« Ответ #4 : 12 июня 2011, 18:27:05 »

не, не читал, но оптимизма не прибавило. Одно не понятно, причём тут прогрев двигла. На горячем то этого нет. ???
А район ДЗ постоянно оклаждается проходящим воздухом....я так думаю....
Записан
Лучше умереть и чувствовать себя спокойно, чем жить и волноваться!

AUTOPROFI

  • Генерал-майор
  • *
  • Оффлайн Оффлайн
  • Возраст: 55
  • Пол: Мужской
  • Сообщений: 1509
  • Автомобиль: RАNGE ROVER VOGUE
  • Имя: Павел
  • Клубный Сусанин
  • Местоположение: ЛУЧШИИ ГОРОД ЗЕМЛИ .эти слова о тебе МАСКВА . Москва ЗАО
  • Карма: +164/-2
Re: Что то странное творится с машиной!!!
« Ответ #5 : 12 июня 2011, 18:30:35 »

Думаю что ни чего серьезного, к Треилу отношусь с большим уважением, не подведет. Прежде всего почистить дросельную заслонку,у меня было при включении кондея двигатель дерался, глох,не тянул. Щелчки под клапаннои крышкои это гидро компенсатор масло не успел набрать,ведь потом проходит.
Записан
Cчастливыи обладатель  LAND ROVER .     GO BEYOND

pavelpal1963

  • Ефрейтор
  • *
  • Оффлайн Оффлайн
  • Сообщений: 37
  • Карма: +2/-1
Re: Что то странное творится с машиной!!!
« Ответ #6 : 12 июня 2011, 19:00:38 »

Посмотрите что за ошибка может все прояснится.
Записан

UralBlazer

  • Мл. сержант
  • *
  • Оффлайн Оффлайн
  • Возраст: 48
  • Пол: Мужской
  • Сообщений: 74
  • Автомобиль: Chevrolet TrailBlazer LTZ
  • Я зла не помню...Я его записываю!
  • Местоположение: Свердловская область
  • Карма: +0/-0
Re: Что то странное творится с машиной!!!
« Ответ #7 : 12 июня 2011, 19:01:43 »

так то оно так, вот жалею что у нас поблизости сканера ни у кого нет...:-(
Записан
Лучше умереть и чувствовать себя спокойно, чем жить и волноваться!

Morose

  • Администратор
  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 46
  • Пол: Мужской
  • Сообщений: 5467
  • Автомобиль: Blazer-97,GrandVitara-07
  • Имя: Евгений
  • Местоположение: Кубинка<->Петушки
  • Карма: +331/-11
Re: Что то странное творится с машиной!!!
« Ответ #8 : 12 июня 2011, 20:00:59 »

без кода ошибки трудно подсказать, сканер нужен простой, им же читают и многие другие авто,поспрашивать стоит.

другие предположения проверять надо заменой, а покупать за зря запчасти это тоже не серьёзно, проще купить бортовой комп или тот же сканер, благо темы про них на форуме были.
Записан
_______________ _______________ _______________ _____________
Правила форума и другая полезная информация(ссылка)

               Клубный Сервис
В Москве - http://trailblazerclub.ru/...
В Санкт-Петербурге - http://trailblazerclub.ru/...
            Группа WhatsApp
            Канал в Telegram

- Группа в ВК

pavelpal1963

  • Ефрейтор
  • *
  • Оффлайн Оффлайн
  • Сообщений: 37
  • Карма: +2/-1
Re: Что то странное творится с машиной!!!
« Ответ #9 : 12 июня 2011, 23:15:43 »

Сканер нужен OBD2 - на любую иномарку. Запишите код а дальше посмотрите код в таблице (ее Goolver выкладывал). Не старайтесь ехать на GM сервис.
Записан

Мишаня

  • Рядовой
  • *
  • Оффлайн Оффлайн
  • Пол: Мужской
  • Сообщений: 4
  • Карма: +0/-0
Re: Что то странное творится с машиной!!!
« Ответ #10 : 12 июня 2011, 23:57:27 »

Было подобное прошлой зимой.Машину на холостых трясло,разгонялась вяло. Как раз подходило ТО. Поехал к диллеру. Вердикт: крысы прогрызли проводку. Случай не гарантийный. Цена 4500р.
Записан

saga

  • Мл. Лейтенант
  • *
  • Оффлайн Оффлайн
  • Возраст: 48
  • Пол: Мужской
  • Сообщений: 338
  • Местоположение: киров
  • Карма: +14/-0
Re: Что то странное творится с машиной!!!
« Ответ #11 : 14 июня 2011, 15:51:23 »

у меня трясло и нетянуло из-за свечей зажигания. из шести три поменял все прошло.
Записан

UralBlazer

  • Мл. сержант
  • *
  • Оффлайн Оффлайн
  • Возраст: 48
  • Пол: Мужской
  • Сообщений: 74
  • Автомобиль: Chevrolet TrailBlazer LTZ
  • Я зла не помню...Я его записываю!
  • Местоположение: Свердловская область
  • Карма: +0/-0
Re: Что то странное творится с машиной!!!
« Ответ #12 : 16 июня 2011, 09:23:34 »

Господа, сегодня узнал код ошибки Р0758 ...но, прочитав инфу на форуме,  так и не понял что она обозначает ???
Записан
Лучше умереть и чувствовать себя спокойно, чем жить и волноваться!

GooLYVER

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 48
  • Пол: Мужской
  • Сообщений: 3508
  • Имя: Сан Саныч
  • ломаю L200/FX35 по очереди ~
  • Местоположение: МО по Ярославке
  • Карма: +1918/-983
Re: Что то странное творится с машиной!!!
« Ответ #13 : 16 июня 2011, 10:01:55 »

 Масло в АКП давно меняли? P0758 - соленоид в плите. Их там два, один  1-2 "А", второй 2-3 "В". Судя по поведению автомобиля, у Вас проблемы с тем, который для 1-2. Стоит в задней части плиты справа (со стороны пассажира, а со стороны водителя для 2-3). Лучше проконсультируй тесь с автоматчиками (например с Фаербердом).
 
« Последнее редактирование: 20 июня 2011, 22:53:13 от GooLYVER »
Записан
Есть технические вопросы? Пишите на broadway@land.ru.

UralBlazer

  • Мл. сержант
  • *
  • Оффлайн Оффлайн
  • Возраст: 48
  • Пол: Мужской
  • Сообщений: 74
  • Автомобиль: Chevrolet TrailBlazer LTZ
  • Я зла не помню...Я его записываю!
  • Местоположение: Свердловская область
  • Карма: +0/-0
Re: Что то странное творится с машиной!!!
« Ответ #14 : 16 июня 2011, 11:26:50 »

масло меняли на 90 т.км....залили Dextron 6...сейчас 110т.км....до этого проблем не было. Исчезает с прогревом....ин тересно почему, и что происходит при отказе этого датчика..
Записан
Лучше умереть и чувствовать себя спокойно, чем жить и волноваться!

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0
Re: Что то странное творится с машиной!!!
« Ответ #15 : 16 июня 2011, 11:55:47 »

DTC P0751 (4.2L)

 


Circuit Description
The 1-2 shift solenoid (SS) valve controls the fluid flow acting on the 1-2 and 3-4 shift valves. The 1-2 SS valve is a normally-open exhaust valve that is used with the 2-3 SS valve, in order to allow 4 different shifting combinations.

If the powertrain control module (PCM) detects a 2-2-3-3 shift pattern, then DTC P0751 sets. DTC P0751 is a type B DTC.

DTC Descriptor
This diagnostic procedure supports the following DTC:

DTC P0751 1-2 Shift Solenoid Valve Performance - No First or Fourth Gear

Conditions for Running the DTC
    •  No VSS DTCs P0502 or P0503.

    •  No TCC stuck ON DTC P0742.

    •  No 1-2 SS valve DTC P0753.

    •  No 2-3 SS valve DTC P0758.

    •  No TP sensor DTCs P1120 or P1220.

    •  The engine speed is greater than 450 RPM for 5 seconds.

    •  The engine is not in fuel cutoff.

    •  The gear range is D4.

    •  The TP angle is 10 percent or greater.

    •  The transmission fluid temperature is 20-130°C (68-266°F).

    •  The system voltage is 10-18 volts.

    •  The engine torque is 68-542 N·m (50-400 lb ft).

    •  The transmission output speed is 150 RPM or greater.

    •  The transfer case ratio in 4WD Low is 0.9 to 1.2.

    •  The transfer case ratio in 4WD High is 2.6 to 2.85.

Conditions for Setting the DTC
DTC P0751 sets if both of the following conditions occur twice:

Condition 1
    •  The PCM commands first gear for 2 seconds.

    •  The estimated gear ratio is 1.2-1.8.

    •  The torque converter efficiency is greater than or equal to 0.35.

    •  All conditions are met for 0.5 seconds.

Condition 2
    •  The PCM commands fourth gear for 1 second.

    •  The estimated gear ratio is 0.95-1.15.

    •  All conditions are met for 6 seconds.

Action Taken When the DTC Sets
    •  The PCM illuminates the malfunction indicator lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC are met.

    •  The PCM commands D2 line pressure.

    •  The PCM commands TCC OFF.

    •  The PCM inhibits fourth gear in hot mode.

    •  The PCM freezes transmission adaptive functions.

    •  The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze Frame and Failure Records.

    •  The PCM stores DTC P0751 in PCM history.

Conditions for Clearing the MIL/DTC
    •  The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.

    •  A scan tool can clear the MIL/DTC.

    •  The PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without an emission-related diagnostic fault occurring.

    •  The PCM cancels the DTC default actions when the fault no longer exists and/or the ignition switch is OFF long enough in order to power down the PCM.

Diagnostic Aids
    •  Verify that the transmission meets the specifications in the table Shift Speed .

    •  Refer to the table Shift Solenoid Valve State and Gear Ratio .

Test Description
The numbers below refer to the step numbers on the diagnostic table.

This step tests that the PCM commanded all shifts, that all shift solenoid valves responded correctly, but that all the shifts did not occur.

DTC P0751 (4.2L) Step
 Action
 Yes
 No
 
1
 Did you perform the Diagnostic System Check - Vehicle?
 Go to Step 2
 Go to Diagnostic System Check - Vehicle
 
2
 Install a scan tool.
Turn ON the ignition, with the engine OFF.
Important: Before clearing the DTC, use the scan tool in order to record the Freeze Frame and Failure Records. Using the Clear Info function erases the Freeze Frame and Failure Records from the powertrain control module (PCM).

Record the DTC Freeze Frame and Failure Records.
Clear the DTC.
Drive the vehicle in D4 range under the following conditions:
Accelerate the vehicle, ensuring that the PCM commands 1st, 2nd, 3rd and 4th gears.

Did you detect a 2-2-3-3 shift pattern?
 Go to Step 3
 Go to Testing for Intermittent Conditions and Poor Connections
 
3
 Inspect the shift solenoid/hydraulic circuit for the following conditions:

    •  An internal malfunction

    •  Damaged seals on the shift solenoid valve

         Refer to Shift Solenoid Leak Test .

Did you find and correct the condition?
 Go to Step 4
 --
 
4
 Perform the following procedure in order to verify the repair:

Select DTC.
Select Clear Info.
Drive the vehicle in D4 range under the following conditions, only if traffic and road conditions permit:
Hold the throttle at 20 percent and accelerate to 88 km/h (55 mph).

Select Specific DTC.
Enter DTC P0751.
Has the test run and passed?
 Go to Step 5
 Go to Step 2
 
5
 With the scan tool, observe the stored information, capture info, and DTC Info.

Does the scan tool display any DTCs that you have not diagnosed?
 



Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0
Re: Что то странное творится с машиной!!!
« Ответ #16 : 16 июня 2011, 11:56:16 »

DTC P0752 (4.2L)

 


Circuit Description
The 1-2 shift solenoid (SS) valve controls the fluid flow acting on the 1-2 and 3-4 shift valves. The 1-2 SS valve is a normally-open exhaust valve that is used with the 2-3 SS valve, in order to allow 4 different shifting combinations.

When the powertrain control module (PCM) detects a 1-1-4-4 shift pattern, then DTC P0752 sets. DTC P0752 is a type B DTC.

DTC Descriptor
This diagnostic procedure supports the following DTC:

DTC P0752 1-2 Shift Solenoid Valve Performance - No Second or Third Gear

Conditions for Running the DTC
    •  No VSS DTCs P0502 or P0503.

    •  No TCC solenoid valve DTC P0740.

    •  No TCC stuck ON DTC P0742.

    •  No 1-2 SS valve DTC P0753.

    •  No 2-3 SS valve DTC P0758.

    •  No 3-2 SS valve assembly DTC P0785.

    •  No TP sensor DTCs P1120 or P1220.

    •  No TFP manual valve position switch DTC P1810.

    •  No TCC PWM solenoid valve DTC P2761.

    •  The engine speed is greater than 450 RPM for 5 seconds.

    •  The engine is not in fuel cutoff.

    •  The gear range is D4.

    •  The TP angle is 10 percent or greater.

    •  The transmission fluid temperature is 20-130°C (68-266°F).

    •  The system voltage is 10-18 volts.

    •  The transmission output speed is 150 RPM or greater.

    •  The transfer case ratio in 4WD Low is 0.9-1.2.

    •  The transfer case ratio in 4WD High is 2.6 to 2.85.

Conditions for Setting the DTC
DTC P0752 sets if both of the following conditions occur twice:

Condition 1
    •  The PCM commands second gear for 1 second.

    •  The torque converter efficiency is greater than or equal to 0.5.

    •  The estimated gear ratio is 3.0-3.3.

    •  The engine torque is 34-542 N·m (25-400 lb ft).

    •  All conditions are met for 2 seconds.

Condition 2
    •  The PCM commands third gear for 1 second.

    •  The torque converter efficiency is greater than or equal to 0.5.

    •  The estimated gear ratio is 0.65-0.9.

    •  The engine torque is 68-542 N·m (50-400 lb ft).

    •  All conditions are met for 3 seconds.

Action Taken When the DTC Sets
    •  The PCM illuminates the malfunction indicator lamp (MIL) 2nd trip.

    •  The PCM commands D2 line pressure.

    •  The PCM inhibits 3-2 downshifts if the vehicle speed is greater than 48 km/h (30 mph) or greater.

    •  The PCM freezes transmission adaptive functions.

    •  The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze Frame and Failure Records.

    •  The PCM stores DTC P0752 in PCM history.

Conditions for Clearing the MIL/DTC
    •  The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.

    •  A scan tool can clear the MIL/DTC.

    •  The PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without an emission-related diagnostic fault occurring.

    •  The PCM cancels the DTC default actions when the fault no longer exists and/or the ignition switch is OFF long enough in order to power down the PCM.

Diagnostic Aids
    •  Verify that the transmission meets the specifications in the table Shift Speed .

    •  Other internal transmission failures may cause more than one shift to occur.

    •  Refer to the table Shift Solenoid Valve State and Gear Ratio .

Test Description
The numbers below refer to the step numbers on the diagnostic table.

This step tests that the PCM commanded all shifts, that all shift solenoid valves responded correctly, but that all the shifts did not occur.

DTC P0752 (4.2L) Step
 Action
 Yes
 No
 
1
 Did you perform the Diagnostic System Check - Vehicle?
 Go to Step 2
 Go to Diagnostic System Check - Vehicle
 
2
 Install a scan tool.
Turn ON the ignition, with the engine OFF.
Important: Before clearing the DTC, use the scan tool in order to record the Freeze Frame and Failure Records. Using the Clear Info function erases the Freeze Frame and Failure Records from the powertrain control module (PCM).

Record the DTC Freeze Frame and Failure Records.
Clear the DTC.
Drive the vehicle in D4 range under the following conditions:
Accelerate the vehicle, ensuring that the PCM commands 1st, 2nd, 3rd, and 4th gears.

Did you detect a 1-1-4-4 shift pattern?
 Go to Step 3
 Go to Testing for Intermittent Conditions and Poor Connections
 
3
 Inspect the shift solenoid/hydraulic circuit for the following conditions:

    •  An internal malfunction

    •  Damaged seals on the shift solenoid valve

         Refer to Shift Solenoid Leak Test .

Did you find and correct the condition?
 Go to Step 4
 --
 
4
 Perform the following procedure in order to verify the repair:

Select DTC.
Select Clear Info.
Drive the vehicle in D4 range under the following conditions, only if traffic and road conditions permit:
Hold the throttle at 20 percent and accelerate to 88 km/h (55 mph).

Select Specific DTC.
Enter DTC P0752.
Has the test run and passed?
 Go to Step 5
 Go to Step 2
 
5
 With the scan tool, observe the stored information, capture info, and DTC Info.

Does the scan tool display any DTCs that you have not diagnosed?
 
Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0
Re: Что то странное творится с машиной!!!
« Ответ #17 : 16 июня 2011, 11:56:54 »

DTC P0756 (4.2L)

 


Circuit Description
The 2-3 shift solenoid (SS) valve controls the fluid flow acting on the 2-3 shift valves. The 2-3 SS valve is a normally-open exhaust valve that is used with the 1-2 SS valve, in order to allow 4 different shifting combinations.

When the powertrain control module (PCM) detects a 4-3-3-4 shift pattern, then DTC P0756 sets. DTC P0756 is a type A DTC.

DTC Descriptor
This diagnostic procedure supports the following DTC:

DTC P0756 2-3 Shift Solenoid Valve Performance - No First or Second Gear

Conditions for Running the DTC
    •  No TP sensor DTCs P0122 or P0123.

    •  No VSS DTCs P0502 or P0503.

    •  No TCC solenoid valve DTC P0740.

    •  No TCC stuck ON DTC P0742.

    •  No 1-2 SS valve DTC P0753.

    •  No 2-3 SS valve DTC P0758.

    •  No 3-2 SS valve assembly DTC P0785.

    •  No TFP manual valve position switch DTC P1810.

    •  No TCC PWM solenoid valve DTC P2761.

    •  The engine speed is greater than 450 RPM for 5 seconds.

    •  The engine is not in fuel cutoff.

    •  The gear range is D4.

    •  The TP angle is 10 percent or greater.

    •  The transmission fluid temperature is 20-130°C (68-266°F).

    •  The system voltage is 10-18 volts.

    •  The engine torque is 68-542 N·m (50-400 lb ft).

    •  The transmission output speed is 150 RPM or greater.

Conditions for Setting the DTC
DTC P0756 sets if both of the following conditions occur:

Condition 1
    •  The PCM commands first gear for 2 seconds.

    •  The estimated gear ratio is 0 to 1.4.

    •  All conditions are met for 1 second.

Condition 2
    •  The PCM commands second gear for 1 second.

    •  The torque converter efficiency is greater than or equal to 0.5.

    •  The estimated gear ratio is 0.9-1.2.

    •  All conditions are met for 2 seconds.

Action Taken When the DTC Sets
    •  The PCM illuminates the malfunction indicator lamp (MIL).

    •  The PCM commands third gear only.

    •  The PCM commands maximum line pressure.

    •  The PCM inhibits TCC engagement.

    •  The PCM freezes transmission adaptive functions.

    •  The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze Frame and Failure Records.

    •  The PCM stores DTC P0756 in PCM history.

Conditions for Clearing the MIL/DTC
    •  The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.

    •  A scan tool can clear the MIL/DTC.

    •  The PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without an emission-related diagnostic fault occurring.

    •  The PCM cancels the DTC default actions when the fault no longer exists and/or the ignition switch is OFF long enough in order to power down the PCM.

Diagnostic Aids
    •  Verify that the transmission meets the specifications in the table Shift Speed .

    •  Other internal transmission failures may cause more than one shift to occur.

    •  Refer to the table Shift Solenoid Valve State and Gear Ratio .

Test Description
The numbers below refer to the step numbers on the diagnostic table.

This step tests that the PCM commanded all shifts, that all shift solenoid valves responded correctly, but that all the shifts did not occur.

DTC P0756 (4.2L) Step
 Action
 Yes
 No
 
1
 Did you perform the Diagnostic System Check - Vehicle?
 Go to Step 2
 Go to Diagnostic System Check - Vehicle
 
2
 Install a scan tool.
Turn ON the ignition, with the engine OFF.
Important: Before clearing the DTC, use the scan tool in order to record the Freeze Frame and Failure Records. Using the Clear Info function erases the Freeze Frame and Failure Records from the powertrain control module (PCM).

Record the DTC Freeze Frame and Failure Records.
Clear the DTC.
Drive the vehicle in D4 range under the following conditions:
Accelerate the vehicle, ensuring that the PCM commands 1st, 2nd, 3rd, and 4th gears.

Did you detect a 4-3-3-4 shift pattern?
 Go to Step 3
 Go to Diagnostic Aids
 
3
 Inspect the shift solenoid/hydraulic circuit for the following conditions:
•  Debris or chips in the AFL oil passage

•  Debris or chips restricting oil flow in passage #29 of the case or through the spacer plate gasket into the valve body

•  A cracked 2-3 shift solenoid

•  A 2-3 shift valve which is stuck or hung up in the valve body bore

•  A 2-3 shuttle valve which is stuck or hung up in its bore

•  Damaged seals on the shift solenoid valves

•  Refer to Shift Solenoid Leak Test .

Clean and inspect the related valves, bores and the valve body for debris or contamination.
Did you find and correct the condition?
 Go to Step 4
 --
 
4
 Perform the following procedure in order to verify the repair:

Select DTC.
Select Clear Info.
Drive the vehicle in D4 range under the following conditions, only if traffic and road conditions permit:
Hold the throttle at 40 percent and accelerate to 64 km/h (40 mph).

Select Specific DTC.
Enter DTC P0756.
Has the test run and passed?
 Go to Step 5
 Go to Step 2
 
5
 With the scan tool, observe the stored information, capture info, and DTC Info.

Does the scan tool display any DTCs that you have not diagnosed?
 Go to Diagnostic Trouble Code (DTC) List - Vehicle
 System OK
 
Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0
Re: Что то странное творится с машиной!!!
« Ответ #18 : 16 июня 2011, 11:57:28 »

DTC P0894 (4.2L)

 


Circuit Description
The powertrain control module (PCM) monitors the difference between engine speed and transmission output speed. In D3 drive range with the torque converter clutch (TCC) engaged, the engine speed should closely match the transmission output speed. In D4 drive range, with the TCC engaged, the TCC slip speed should be -20 to +50 RPM.

When the PCM detects excessive TCC slip when the TCC should be engaged, then DTC P0894 sets. DTC P0894 is a type B DTC.

DTC Descriptor
This diagnostic procedure supports the following DTC:

DTC P0894 Transmission Component Slipping

Conditions for Running the DTC
    •  No TP sensor DTCs P1120 or P1220.

    •  No VSS DTCs P0502 or P0503.

    •  No TCC solenoid valve DTC P0740.

    •  No 1-2 SS valve DTC P0753.

    •  No 2-3 SS valve DTC P0758.

    •  No 3-2 SS valve assembly DTC P0785.

    •  No TFP manual valve position switch DTC P1810.

    •  No TCC PWM solenoid valve DTC P2761.

    •  The engine speed is greater than 450 RPM for 5 seconds.

    •  The engine is not in fuel cutoff.

    •  The engine torque is 68-542 N·m (50-400 lb ft).

    •  The TP angle is 20-99 percent.

    •  The vehicle speed is 48-131 km/h (30-82 mph).

    •  The engine speed is 1,500-3,000 RPM.

    •  The speed ratio is 0.69-0.88, speed ratio is engine speed divided by the transmission output speed.

    •  The gear range is D4.

    •  The commanded gear is not 1st gear.

    •  The TFT is 20-150°C (68-302°F).

    •  The shift solenoid performance diagnostic counters are zero.

Conditions for Setting the DTC
DTC P0894 sets if the following conditions occur for 3 TCC cycles.

    •  The TCC is commanded ON for 5 seconds.

    •  The TCC is at 40 percent duty cycle for 5 seconds.

    •  The TCC slip speed is 130-800 RPM for 7 seconds.


        Important: The following actions may occur before the DTC sets. 


    •  If the TCC is commanded ON for 5 seconds, the TCC is at 40 percent duty cycle for 5 seconds, the TP angle is 20-99 percent and the transmission slip counter has incremented to either 1 or 2, out of 3 to increment the fail counter for the current ignition cycle, then the following slip conditions and actions may increment the fail counter for the current ignition cycle:

         These conditions must occur sequentially.

Condition 1
If the TCC slip speed is 130-800 RPM for 7 seconds, then the PCM will command maximum line pressure and freeze shift adapts from being updated.

Condition 2
If Condition 1 is met and the TCC slip speed is 130-800 RPM for 7 seconds, then the PCM will command the TCC Off for 1.5 seconds.

Condition 3
If Condition 2 is met and the TCC slip speed is 130-800 RPM for 7 seconds, then the fail counter on the current ignition cycle is incremented.

The above slip conditions and actions may be disregarded if the TCC is commanded OFF at any time as a result of a driving maneuver, sudden acceleration or deceleration.

Action Taken When the DTC Sets
    •  The PCM illuminates the malfunction indicator lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC are met.

    •  The PCM commands maximum line pressure.

    •  The PCM inhibits TCC engagement.

    •  The PCM inhibits 4th gear if the transmission is in hot mode.

    •  The TCM freezes transmission adaptive functions.

    •  The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze Frame and Failure Records.

    •  The PCM stores DTC P0894 in PCM history during the second consecutive trip in which the Conditions for Setting the DTC are met.

Conditions for Clearing the MIL/DTC
    •  The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.

    •  A scan tool can clear the MIL/DTC.

    •  The PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without an emission-related diagnostic fault occurring.

    •  The PCM cancels the DTC default actions when the fault no longer exists and/or the ignition switch is OFF long enough in order to power down the PCM.

Diagnostic Aids
    •  Bronze material found in the transmission oil pan may indicate stator shaft bushing wear. If bushing wear is suspected, inspect the stator shaft and the input, turbine, shaft for damage.

    •  Refer to Symptoms - Automatic Transmission for more information.

Test Description
The numbers below refer to the step numbers on the diagnostic table.

This step tests the torque converter for slippage while in a commanded lock-up state.

DTC P0894 (4.2L) Step
 Action
 Values
 Yes
 No
 
1
 Did you perform the Diagnostic System Check - Vehicle?
 --
 Go to Step 2
 Go to Diagnostic System Check - Vehicle
 
2
 Inspect for correct transmission fluid level.

Refer to Transmission Fluid Check .

Did you perform the fluid checking procedure?
 --
 Go to Step 3
 Go to Transmission Fluid Check
 
3
 Install a scan tool.
Turn ON the ignition, with the engine OFF.
Important: Before clearing the DTC, use the scan tool in order to record the Freeze Frame and Failure Records. Using the Clear Info function erases the Freeze Frame and Failure Records from the powertrain control module (PCM).

Record the DTC Freeze Frame and Failure Records.
Clear the DTC.
Important: It may be necessary to allow multiple TCC cycles to occur in order to verify a slipping condition. It may also be necessary to ensure the transmission is warm before performing this step.

Drive the vehicle in 4th gear with the TCC commanded ON.
Does the scan tool TCC Slip Speed measure within the specified range for 7 seconds?
 130-800 RPM
 Go to Step 4
 Go to Testing for Intermittent Conditions and Poor Connections
 
4
 Inspect the torque converter clutch (TCC) solenoid valve for the following conditions:
•  Internal malfunction, such as sediment or damage

•  Damaged seals

•  Refer to Torque Converter Clutch Pulse Width Modulation Solenoid, Torque Converter Clutch Solenoid, and Wiring Harness .

Inspect the torque converter clutch pulse width modulation (TCC PWM) solenoid valve for the following conditions:
•  Internal malfunction, such as sediment or damage

•  Damaged seals

•  Refer to Torque Converter Clutch Pulse Width Modulation Solenoid, Torque Converter Clutch Solenoid, and Wiring Harness .

Did you find and correct the condition?
 --
 Go to Step 14
 Go to Step 5
 
5
 Inspect the 1-2 shift solenoid (SS) valve for the following conditions:
•  Internal malfunction, such as sediment or damage

•  Damaged seals

•  Refer to Shift Solenoid Leak Test .

Inspect the 2-3 shift solenoid (SS) valve for the following conditions:
•  Internal malfunction, such as sediment or damage

•  Damaged seals

•  Refer to Shift Solenoid Leak Test .

Inspect the 3-2 shift solenoid valve assembly for the following conditions:
•  Internal malfunction, such as sediment or damage

•  Damaged seals

•  Refer to Shift Solenoid Leak Test .

Did you find and correct the condition?
 --
 Go to Step 14
 Go to Step 6
 
6
 Inspect the valve body assembly for the following conditions:

    •  Stuck regulator apply valve

    •  Scored regulator apply valve body

         Refer to Control Valve Body Disassemble .

Did you find and correct the condition?
 --
 Go to Step 13
 Go to Step 7
 
7
 Inspect the torque converter assembly for the following conditions:

    •  Front stator shaft bushing for wear

    •  Stator roller clutch not holding

    •  External damage/leaks

         Refer to Torque Converter End Play Specifications .

Did you find and correct the condition?
 --
 Go to Step 13
 Go to Step 8
 
8
 Inspect the oil pump assembly for the following conditions:

    •  A stuck converter clutch valve

    •  The converter clutch valve is assembled backwards

    •  A mispositioned converter clutch valve retaining ring

    •  A cocked converter clutch outer valve spring

    •  A mispositioned pump to case gasket

    •  Restricted orifice cup plugs

    •  Damaged orifice cup plugs

    •  Over-tightened, or unevenly tightened pump body to cover bolts

Refer to Oil Pump Cover Disassemble .

Did you find and correct the condition?
 --
 Go to Step 13
 Go to Step 9
 
9
 Inspect the input housing and shaft assembly for the following conditions:

    •  Cut turbine shaft O-ring seal

    •  Damaged turbine shaft O-ring seal

    •  Restricted turbine shaft retainer and ball assembly

    •  Damaged turbine shaft retainer and ball assembly

Refer to Input Housing and Shaft Assembly Inspection .

Did you find and correct the condition?
 --
 Go to Step 13
 Go to Step 10
 
10
 Inspect the 2-4 band assembly for the following conditions:

    •  Worn 2-4 band

    •  Damaged 2-4 band

    •  Mispositioned 2-4 band

    •  Misassembled 2-4 band

    •  The band anchor pin is not engaged

         Refer to 2-4 Band Installation .

Inspect the 2-4 servo assembly for the following conditions:

    •  Restricted apply passages in the 2-4 servo assembly

    •  Blocked apply passages in the 2-4 servo assembly

    •  Nicks or burrs on the 2nd apply piston pin

    •  Damaged 2nd apply piston pin

    •  Incorrect 2nd apply piston pin

    •  Nicks or burrs on the pin bore in the case

    •  Damaged fourth servo piston

    •  Misassembled fourth servo piston

    •  Damaged servo bore in the case

    •  Missing piston seals

    •  Cut piston seals

    •  Damaged piston seals

    •  Porosity in the pistons

    •  Porosity in the cover

    •  Porosity in the case

    •  Damaged piston seal grooves

    •  Plugged orifice cup plug

    •  Missing orifice cup plug

Refer to 2-4 Band Servo 2nd Apply Piston Disassemble , 2-4 Band Servo Piston Pin Length Check and 2-4 Servo Assembly Installation .

Did you find and correct the condition?
 --
 Go to Step 13
 Go to Step 11
 
11
 Inspect the forward clutch assembly for the following conditions:

    •  Worn clutch plates

    •  Porosity in the forward clutch piston

    •  Damaged forward clutch piston

    •  Missing forward clutch piston inner and outer seals

    •  Cut forward clutch piston inner and outer seals

    •  Damaged forward clutch piston inner and outer seals

    •  Missing input housing to forward clutch housing O-ring seal

    •  Cut input housing to forward clutch housing O-ring seal

    •  Damaged input housing to forward clutch housing O-ring seal

    •  Damaged forward clutch housing

    •  Damaged forward clutch housing retainer and ball assembly

    •  Forward clutch housing retainer and ball assembly is not sealing

Refer to Forward Clutch Assembly Assemble .

Did you find and correct the condition?
 --
 Go to Step 13
 Go to Step 12
 
12
 Inspect the 3-4 clutch assembly for the following conditions:

    •  Worn clutch plates

    •  Porosity in the 3-4 clutch piston

    •  Damaged 3-4 clutch piston

    •  Missing 3-4 clutch inner and outer seals

    •  Cut 3-4 clutch inner and outer seals

    •  Damaged 3-4 clutch inner and outer seals

    •  Damaged 3-4 clutch spring assembly

    •  Damaged 3-4 clutch apply ring

    •  Damaged piston seal grooves

    •  Plugged orifice cup plug

    •  Missing orifice cup plug

Refer to 3-4 Clutch Assemble and 3-4 Clutch Plate Travel Check .

Did you find and correct the condition?
 --
 Go to Step 13
 Go to Testing for Intermittent Conditions and Poor Connections
 
13
 Change the AT fluid and filter.
Inspect for correct transmission fluid level.
Refer to Transmission Fluid Check .

Add new AT fluid as necessary.
Important: Performing the Service Procedure to Clear TAP will clear all adapt cells. This may affect Transmission performance. The PCM will update the transmission adapt cell values as the vehicle is driven.

With a scan tool perform the Clear TAP function.
Did you complete the above procedure?
 --
 Go to Step 14
 --
 
14
 Perform the following procedure in order to verify the repair:

Select DTC.
Select Clear Info.
Operate the vehicle under the following conditions:
•  Drive the vehicle in D4, with the TCC ON, and a throttle position of 20-99%.

•  Ensure that the scan tool TCC Slip Speed is -20 to +50 RPM for at least 7 seconds.

Select Specific DTC.
Enter DTC P0894.
Has the test run and passed?
 --
 Go to Step 15
 Go to Step 2
 
15
 With the scan tool, observe the stored information, capture info, and DTC Info.

Does the scan tool display any DTCs that you have not diagnosed?
 --
 Go to Diagnostic Trouble Code (DTC) List - Vehicle
 System OK
 
Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0
Re: Что то странное творится с машиной!!!
« Ответ #19 : 16 июня 2011, 11:58:00 »

DTC P2771 (4.2L)

 


Circuit Description
The four wheel drive (4WD) low circuit consists of the powertrain control module (PCM), a transfer case control module and the circuit wiring. The transfer case control module controls the 4WD low signal circuit. When the operator selects 4WD low, the transfer case control module grounds the signal circuit, and the 4WD low signal voltage on the circuit changes from ignition voltage to zero volts. The PCM then compensates for transfer case gear reduction in the transmission output shaft speed (OSS) sensor signal. The PCM uses the transmission OSS sensor signal to adjust shift points, line pressure and torque converter clutch (TCC) scheduling.

When the PCM detects a continuous open, short to ground or short to power in the 4WD low circuit, then DTC P2771 sets. DTC P2771 is a type B DTC.

DTC Descriptor
This diagnostic procedure supports the following DTC:

DTC P2771 Four Wheel Drive (4WD) Low Switch Circuit

Conditions for Running the DTC
    •  No TP sensor DTCs P0122, or P0123.

    •  No VSS assembly DTCs P0502 or P0503.

    •  No TCC solenoid valve DTC P0740.

    •  No TCC stuck ON DTC P0742.

    •  No 1-2 SS valve DTCs P0751 or P0753.

    •  No 2-3 SS valve DTCs P0756 or P0758.

    •  No TFP manual valve position switch DTC P1810.

    •  No TCC PWM solenoid valve DTC P2761.

    •  The engine speed is greater than 450 RPM for 5 seconds.

    •  The engine is not in fuel cutoff.

    •  The vehicle speed is greater than 11 km/h (7 mph).

    •  The TP angle is 17-50 percent.

    •  The engine torque is 54-542 N·m (40-400 lb ft).

    •  The engine vacuum is 0-105 kPa (0-15 psi).

    •  The gear range is D4.

    •  The shift solenoid performance counters are zero.

    •  The TFT is 20-130°C (68-266°F).

Conditions for Setting the DTC
DTC P2771 sets if one of the following conditions occurs:

Condition 1
    •  The 4WD low switch is in 4WD low.

    •  The transfer case is not in 4WD low.

    •  The TCC slip speed is -3,000 to -50 RPM.

    •  The transfer case ratio is 0.08-1.2, the transfer case ratio is the engine speed divided by the transfer case output speed.

    •  All conditions are met for 5 seconds.

Condition 2
    •  The 4WD low switch is not in 4WD low.

    •  The transfer case is in 4WD low.

    •  The TCC is commanded ON.

    •  The TCC slip speed is 100 to 3,000 RPM.

    •  The transfer case ratio is 2.5-2.9.

    •  All conditions are met for 10 seconds.

Action Taken When the DTC Sets
    •  The PCM illuminates the malfunction indicator lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC are met.

    •  The PCM commands a normal shift pattern, not a 4WD low shift pattern.

    •  The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze Frame and Failure Records.

    •  The PCM stores DTC P2771 in PCM history during the second consecutive trip in which the Conditions for Setting the DTC are met.

Conditions for Clearing the MIL/DTC
    •  The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.

    •  A scan tool can clear the MIL/DTC.

    •  The PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without an emission-related diagnostic fault occurring.

    •  The PCM cancels the DTC default actions when the fault no longer exists and/or the ignition switch is OFF long enough in order to power down the PCM.

Diagnostic Aids
    •  Verify that the input speed sensor (ISS) and the output speed sensor (OSS) are functioning properly.

    •  In 3rd gear at approximately 64 km/h (40 mph), command TCC ON. If functioning properly the OSS will track ISS and the engine RPM.

    •  If not, refer to DTC P0716 for the ISS and DTC P0723 for the OSS.

Test Description
The numbers below refer to the step numbers on the diagnostic table.

This step tests for a short to ground in the 4WD low signal circuit.

This step tests for an open in the 4WD low signal circuit or a faulty transfer case control module.

DTC P2771 (4.2L) Step
 Action
 Values
 Yes
 No
 
1
 Did you perform the Diagnostic System Check - Vehicle?
 --
 Go to Step 2
 Go to Diagnostic System Check - Vehicle
 
2
 Install a scan tool.
Start the engine, parking brake disengaged.
Important: Before clearing the DTC, use the scan tool in order to record the Freeze Frame and Failure Records. Using the Clear Info function erases the Freeze Frame and Failure Records from the powertrain control module (PCM).

Record the DTC Freeze Frame and Failure Records.
Clear the DTC.
Place the transmission in NEUTRAL.
Select 4HI on the transfer case selector.
Important: It may be necessary to drive the vehicle slightly forward to engage 4LO on the transfer case.

Select 4LO on the transfer case selector.
Does the scan tool 4WD Low display Disabled when you select 4HI, then Enabled when you select 4LO?
 --
 Go to Testing for Intermittent Conditions and Poor Connections
 Go to Step 3
 
3
 Turn OFF the ignition.
Disconnect the transfer case control module connector.
Turn ON the ignition, with the engine OFF.
Does the scan tool 4WD Low indicate Enabled?
 --
 Go to Step 6
 Go to Step 4
 
4
 Connect a fused jumper between the harness side of the 4WD low signal circuit and ground at the transfer case control module connector.
Observe the scan tool 4WD Low parameter.
Does the scan tool 4WD Low parameter indicate Enabled when the 4WD low signal circuit, is grounded?
 --
 Go to Step 5
 Go to Step 7
 
5
 Replace the transfer case control module.

Refer to Control Module References for replacement, setup and programming.

Did you complete the replacement?
 --
 Go to Step 9
 --
 
6
 Test the 4WD low signal circuit for a short to ground.

Refer to Testing for Short to Ground and Wiring Repairs .

Did you find and correct the condition?
 --
 Go to Step 9
 Go to Step 8
 
7
 Test the 4WD low signal circuit for an open.

Refer to Testing for Continuity and Wiring Repairs .

Did you find and correct the condition?
 --
 Go to Step 9
 Go to Step 8
 
8
 Replace the PCM.

Refer to Control Module References for replacement, setup and programming.

Did you complete the replacement?
 --
 Go to Step 9
 --
 
9
 Perform the following procedure in order to verify the repair:

Select DTC.
Select Clear Info.
Operate the vehicle under the following conditions:
3.1.  Select 4LO on the transfer case selector.

3.2.  Drive the vehicle in D4.

3.3.  Verify that the speed ratio is 2.5-2.9 for 1.5 seconds.

3.4.  Select 2HI or 4HI on the transfer case selector.

3.5.  Drive the vehicle in D4 with the TCC ON.

3.6.  Verify that the speed ratio is 0.8-1.2 for 5 seconds.

Select Specific DTC.
Enter DTC P2771.
Has the test run and passed?
 --
 Go to Step 10
 Go to Step 2
 
10
 With the scan tool, observe the stored information, capture info, and DTC Info.

Does the scan tool display any DTCs that you have not diagnosed?
 --
 Go to Diagnostic Trouble Code (DTC) List - Vehicle
 System OK
 
Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0
Re: Что то странное творится с машиной!!!
« Ответ #20 : 16 июня 2011, 11:59:00 »

#01-07-30-036G: Diagnostic Tips for Automatic Transmission DTC P0756, Second, Third, Fourth Gear Start - (May 12, 2008)

 
Subject: Diagnostic Tips for Automatic Transmission DTC P0756, Second, Third, Fourth Gear Start


Models: 2008 and Prior Passenger Cars and Light Duty Trucks

 2008 and Prior HUMMER H2, H3

 2008 and Prior Saab 9-7X

 with 4L60-E, 4L65-E or 4L70-E Automatic Transmission (RPOs M30, M32 or M70)




--------------------------------------------------------------------------------

This bulletin is being revised to add the 2008 model year. Please discard Corporate Bulletin Number 01-07-30-036F (Section 07 - Transmission/Transaxle).


--------------------------------------------------------------------------------

Some dealership technicians may have difficulty diagnosing DTC P0756, 2-3 Shift Valve Performance on 4L60-E, 4L65-E or 4L70-E automatic transmissions. As detailed in the Service Manual, when the PCM detects a 4-3-3-4 shift pattern, DTC P0756 will set. Some customers may also describe a condition of a second, third or forth gear start that may have the same causes but has not set this DTC yet. Below are some tips when diagnosing this DTC:

    •  This is a performance code. This means that a mechanical malfunction exists.

    •  This code is not set by electrical issues such as a damaged wiring harness or poor electrical connections. Electrical problems would cause a DTC P0758, P0787 or P0788 to set.

    •  The most likely cause is chips/debris plugging the filtered AFL oil at orifice #29 on the top of the spacer plate (48). This is a very small hole and is easily plugged by a small amount of debris. It is important to remove the spacer plate and inspect orifice #29 and the immediate area for the presence of chips/debris. Also, the transmission case passage directly above this orifice and the valve body passage directly below should be inspected and cleaned of any chips/debris.

    •  This code could be set if the 2-3 shift valve (368) were stuck or hung-up in its bore. Inspect the 2-3 shift valve (368) and the 2-3 shuttle valve (369) for free movement or damage and clean the valves, the bore and the valve body passages.

    •  This code could be set by a 2-3 shift solenoid (367b) if it were cracked, broken or leaking. Refer to Shift Solenoid Leak Test in the appropriate Service Manual for the leak test procedure. Based on parts return findings, a damaged or leaking shift solenoid is the least likely cause of this condition. Simply replacing a shift solenoid will not correct this condition unless the solenoid has been found to be cracked, broken or leaking.

It is important to also refer to the appropriate Service Manual or Service Information (SI) for further possible causes of this condition.
Записан

UralBlazer

  • Мл. сержант
  • *
  • Оффлайн Оффлайн
  • Возраст: 48
  • Пол: Мужской
  • Сообщений: 74
  • Автомобиль: Chevrolet TrailBlazer LTZ
  • Я зла не помню...Я его записываю!
  • Местоположение: Свердловская область
  • Карма: +0/-0
Re: Что то странное творится с машиной!!!
« Ответ #21 : 16 июня 2011, 12:07:40 »

 :o :o :o
а теперь по-русски, копи-пастер!
Записан
Лучше умереть и чувствовать себя спокойно, чем жить и волноваться!

Morose

  • Администратор
  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 46
  • Пол: Мужской
  • Сообщений: 5467
  • Автомобиль: Blazer-97,GrandVitara-07
  • Имя: Евгений
  • Местоположение: Кубинка<->Петушки
  • Карма: +331/-11
Re: Что то странное творится с машиной!!!
« Ответ #22 : 16 июня 2011, 13:29:45 »

по русски подобное не бывает, обычно
Записан
_______________ _______________ _______________ _____________
Правила форума и другая полезная информация(ссылка)

               Клубный Сервис
В Москве - http://trailblazerclub.ru/...
В Санкт-Петербурге - http://trailblazerclub.ru/...
            Группа WhatsApp
            Канал в Telegram

- Группа в ВК

KUBINEZ

  • Модератор Форума
  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 51
  • Пол: Мужской
  • Сообщений: 9518
  • Автомобиль: Chevrolet TrailBlazer LTZ 2006 черный, был... Tahoe LTZ 2012 черный стал
  • Имя: Виктор
  • Местоположение: Москва (Медведково), МО Кубинка
  • Карма: +674/-14
Re: Что то странное творится с машиной!!!
« Ответ #23 : 16 июня 2011, 14:30:15 »

:o :o :o
а теперь по-русски, копи-пастер!


скопируй и через переводчик

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0
Re: Что то странное творится с машиной!!!
« Ответ #24 : 16 июня 2011, 18:38:49 »

установи Google Chrome и читай по русски On-Line
Записан

UralBlazer

  • Мл. сержант
  • *
  • Оффлайн Оффлайн
  • Возраст: 48
  • Пол: Мужской
  • Сообщений: 74
  • Автомобиль: Chevrolet TrailBlazer LTZ
  • Я зла не помню...Я его записываю!
  • Местоположение: Свердловская область
  • Карма: +0/-0
Re: Что то странное творится с машиной!!!
« Ответ #25 : 16 июня 2011, 19:09:22 »

Перевёл, прочитал......п одумал.....А ну его наХ!......
Если там засрало отверстие № 29, то ради него одного снимать поддон и сливать в канаву дефицитный Декстрон 6, без особой надежды исправить, я считаю не целесообразным.
ОДнако многоуважаемый Morose мне подсказал проверить проводку к датчику и фишку, а GooLYVER сказал где всё это находится. Так что думаю в выходные запасусь фонариком и полезу в яму.....
Чё увижу - отпишусь! ;-)

Всем БОЛЬШОЕ спасибо за участие!
Записан
Лучше умереть и чувствовать себя спокойно, чем жить и волноваться!

GooLYVER

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 48
  • Пол: Мужской
  • Сообщений: 3508
  • Имя: Сан Саныч
  • ломаю L200/FX35 по очереди ~
  • Местоположение: МО по Ярославке
  • Карма: +1918/-983
Re: Что то странное творится с машиной!!!
« Ответ #26 : 17 июня 2011, 02:32:13 »

Так что думаю в выходные запасусь фонариком и полезу в яму.....
Чё увижу - отпишусь! ;-)

Всем БОЛЬШОЕ спасибо за участие!

Так это, фонарик не особо поможет.... не сняв поддон все равно не долезешь ни до проводки, ни до соленоида....
Вот киношка нашлась по этому поводу. Так нагляднее, как раз его меняют.

Записан
Есть технические вопросы? Пишите на broadway@land.ru.

UralBlazer

  • Мл. сержант
  • *
  • Оффлайн Оффлайн
  • Возраст: 48
  • Пол: Мужской
  • Сообщений: 74
  • Автомобиль: Chevrolet TrailBlazer LTZ
  • Я зла не помню...Я его записываю!
  • Местоположение: Свердловская область
  • Карма: +0/-0
Re: Что то странное творится с машиной!!!
« Ответ #27 : 17 июня 2011, 07:11:28 »

Блиииин, Гуливерчик, дык где же я теперь в Палермо найду Декстрон 6.....да ещё человека, который не добьёт эту коробку...... :'(
Вопрос: Раз проблема через несколько минут сама устраняется, то можно ли ездить так? Каков механизм "не срабатывания"  этого соленоида? Как это отражается на фрикционах? Я так понял что раз не включается 1-2 передача, то АКПП включает 3-4...?! Следовательно нагрузка на фрикционы больше?
Записан
Лучше умереть и чувствовать себя спокойно, чем жить и волноваться!