Российский Клуб Chevrolet TrailBlazer & Chevrolet Tahoe

Автор Тема: Спасите, 05.09 ехать 700 км!  (Прочитано 7514 раз)

0 Пользователей и 1 Гость просматривают эту тему.

johnyelc

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Пол: Мужской
  • Сообщений: 177
  • Автомобиль: TrailBlazer 2002
  • Имя: Евгений
  • +79529460404
  • Местоположение: г. Новосибирск
  • Карма: +0/-0
Спасите, 05.09 ехать 700 км!
« : 05 сентября 2012, 00:10:23 »

Здравствуйте уважаемые. выручайте!
Поменяли мне катализатор на пламя гаситель и поставили обманку, после этого сразу не заметил, доехал до работы обороты холостые 900!! До этого ошибок не было таких. Жрет как танк! ошибки p0131, p0171 и вроде p0137, скажите куда рыть надо ехать срочно, что сломалось блин!! Бенз пробовал залить 95, бесполезно.
Записан

mvi

  • Майор
  • *
  • Оффлайн Оффлайн
  • Возраст: 49
  • Пол: Мужской
  • Сообщений: 963
  • Автомобиль: Trailblazer 2006 г.LTZ, цвет вороной, Форд Куга 2 Rest,Toyota Sprinter Trueno 88 г.в., и много Яв ))
  • Имя: Вячеслав
  • Местоположение: Иваново
  • Карма: +100/-0
Спасите, 05.09 ехать 700 км!
« Ответ #1 : 05 сентября 2012, 00:35:37 »

Ехать обратно и давать по башке за такую работу. А по сути вопроса надо ошибки расшифровывать. В этом я пока не силён. Народ проснётся может что подскажет. Если отталкиваться от твоих действий с авто, то могу предположить (!), что не угадали с обманкой.
Боюсь напутать, но инет говорит по этим ошибкам - датчик кислорода , слишком бедная смесь. Посмотри сам разъёмы все на месте, провода целы? Попробуй скинуть клемму с АКБ на часок-другой.
Записан
Всё, что ни делается - всё к лучшему, главное сделать правильные выводы!

Manjur

  • Гость
  • Карма: +/-
Спасите, 05.09 ехать 700 км!
« Ответ #2 : 05 сентября 2012, 00:39:05 »

Здравствуйте уважаемые. выручайте!
Поменяли мне катализатор на пламя гаситель и поставили обманку, после этого сразу не заметил, доехал до работы обороты холостые 900!! До этого ошибок не было таких. Жрет как танк! ошибки p0131, p0171 и вроде p0137, скажите куда рыть надо ехать срочно, что сломалось блин!! Бенз пробовал залить 95, бесполезно.
Ошибки точно показывают на бедную топливо - воздушную смесь, и на лямбда - зонд (датчик кислорода). Скорее всего некорректно установлена обманка второго датчика. Эту проблему устраняй там, где вырезал катализатор.
Записан

johnyelc

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Пол: Мужской
  • Сообщений: 177
  • Автомобиль: TrailBlazer 2002
  • Имя: Евгений
  • +79529460404
  • Местоположение: г. Новосибирск
  • Карма: +0/-0
Спасите, 05.09 ехать 700 км!
« Ответ #3 : 05 сентября 2012, 10:07:42 »

Спасибо за реакцию, еду к ним, будем смотреть, позже отпишусь
Записан

Reider

  • Капитан
  • *
  • Оффлайн Оффлайн
  • Возраст: 69
  • Пол: Мужской
  • Сообщений: 675
  • Автомобиль: Tahoe 840, 2004 год, Кёнигсбергская
  • Имя: Александр Валентинович
  • Местоположение: Санкт-Петербург, Петроградская сторона
  • Карма: +6/-0
Спасите, 05.09 ехать 700 км!
« Ответ #4 : 05 сентября 2012, 11:02:20 »

А запахов в салоне или рядом с машиной нет? Выхлопом или недогоревшей смесью (запах напоминает ацетон) не пахнет? Если да - ищите недозатянутые гайки или неуплотнённые соединения в выхлопном тракте, сопротивление на выходе из двигателя недостаточно для полног сгорания смеси.
Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0
Спасите, 05.09 ехать 700 км!
« Ответ #5 : 05 сентября 2012, 12:07:05 »

DTC P0131

Circuit Description

Heated oxygen sensors (HO2S) are used for fuel control and post catalyst monitoring. Each HO2S compares the oxygen content of the surrounding air with the oxygen content in the exhaust stream. The HO2S must reach operating temperature to provide an accurate voltage signal. Heating elements inside the HO2S minimize the time required for the sensors to reach operating temperature. The powertrain control module (PCM) supplies the HO2S with a reference, or bias, voltage of about 450 mV . When the engine is first started the PCM operates in Open Loop, ignoring the HO2S voltage signal. Once the HO2S reaches operating temperatures and Closed Loop is achieved, the HO2S generates a voltage within a range of 0-1,000 mV that fluctuates above and below bias voltage. High HO2S voltage indicates a rich exhaust stream. Low HO2S voltage indicates a lean exhaust stream.

If the PCM detects an HO2S voltage that stays below a specified value, DTC P0131 will set.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0131 HO2S Circuit Low Voltage Sensor 1

Conditions for Running the DTC

DTCs P0068, P0106, P0107, P0108, P0112, P0113, P0117, P0118, P0120, P0122, P0123, P0125, P0128, P0201, P0202, P0203, P0204, P0205, P0206, P0220, P0300-P0306, P0315, P0336, P0442, P0446, P0452, P0453, P0455, P0483, P0496, P0506, P0507, P0601, P0602, P0604, P0606, P060D, P060E, P0641, P0651, P1516, P1621, P2101, P2120, P2125, P2135, P2138, P2176 are not set.
The Engine Coolant Temperature (ECT) Sensor parameter is more than 70°C (158°F) .
The Ignition 1 Signal parameter is more than 10 volts .
The Fuel Level Sensor parameter is more than 10 percent .
The Engine Run Time parameter is more than 10 seconds .
The Loop Status parameter is closed.
The Throttle Position (TP) Indicated Angle parameter is between 15-50 percent .
The Manifold Absolute Pressure (MAP) Sensor parameter is more than 25 kPa .
The Accelerator Pedal Position (APP) Indicated Angle parameter is more than 1.2 percent .
DTC P0131 runs continuously when the above conditions are met for 4 seconds .
Conditions for Setting the DTC

The PCM detects that the HO2S 1 Voltage parameter is less than 52 mV .
DTC P0131 sets within 125 seconds when the above condition is met.
Action Taken When the DTC Sets

The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.
Conditions for Clearing the MIL/DTC

The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
Clear the MIL and the DTC with a scan tool.
Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0
Спасите, 05.09 ехать 700 км!
« Ответ #6 : 05 сентября 2012, 12:07:53 »

DTC P0171

Circuit Description

The powertrain control module (PCM) controls the air/fuel metering system in order to provide the best possible combination of driveability, fuel economy and emission control. Fuel delivery is controlled differently during Open Loop and Closed Loop. During Open Loop, the PCM determines fuel delivery based on sensor signals, without heated oxygen sensor (HO2S) input. During Closed Loop the PCM adds HO2S inputs and level of purge to calculate short and long term fuel trim adjustments. If the HO2S indicates a lean condition, the fuel trim values will be above 0 percent . If the HO2S indicates a rich condition, the fuel trim values will be less than 0 percent . The short term fuel trim values change rapidly in response to the HO2S voltage signals. The long term fuel trim makes coarse adjustments in order to maintain an air/fuel ratio of 14.7:1. A block of cells contain information arranged in combinations of engine RPM and engine load for a full range of vehicle operating conditions. The long term fuel trim diagnostic is based on an average of cells currently being used. The PCM selects the cells based on the engine speed and load. If the PCM detects an excessively lean condition, DTC P0171 sets.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0171 Fuel Trim System Lean

Conditions for Running the DTC

DTCs P0013, P0014, P0017, P0030, P0036, P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0128, P0130, P0131, P0132, P0133, P0134, P0135, P0136, P0137, P0138, P0140, P0141, P0201-P0206, P0220, P0222, P0223, P0230, P0300, P0326, P0327, P0332, P0411, P0412, P0418, P0442, P0443, P0446, P0449, P0451, P0452, P0453, P0454, P0455, P0496, P0502, P0503, P0506, P0507, P060D, P060E, P1101, P1133, P1134, P1380, P1381, P1516, P1681, P2101, P2119, P2120, P2122, P2123, P2125, P2127, P2128, P2135, P2138, P2176, P2430, P2431, P2432, P2433, P2440, P2444 are not set.
The engine is in Closed Loop status.
The engine coolant temperature (ECT) is between -7 and +120°C (+19.4 and +248°F) .
The intake air temperature is between -7 and +145°C (+19.4 and +293°F) .
The manifold absolute pressure (MAP) is between 15-100 kPa (2.2-14.5 psi) .
The mass air flow (MAF) is between 1-512 g/s .
The vehicle speed is less than 132 km/h (82 mph) .
The engine speed is between 400-6,100 RPM .
The barometric pressure is more than 72 kPa (10.4 psi) .
The fuel level is more than 10 percent .
DTC P0171 runs continuously when the above conditions are met.
Conditions for Setting the DTC

The long term fuel trim weighted average value is more than a calibrated value.
The above condition is present for 2 seconds .
Action Taken When the DTC Sets

The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.
Conditions for Clearing the MIL/DTC

The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
Clear the MIL and the DTC with a scan tool.
Diagnostic Aids

Test for fuel contamination. Small amounts of water can be delivered to the fuel injectors and cause a lean exhaust indication. A lean exhaust indication can also be caused by too much alcohol in the fuel.
The system will go lean if an injector is not supplying enough fuel.
A lean condition could be present during high fuel demand due to a fuel pump that does not pump enough fuel.
Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0
Спасите, 05.09 ехать 700 км!
« Ответ #7 : 05 сентября 2012, 12:08:28 »

DTC P0137

Circuit Description

Heated oxygen sensors (HO2S) are used for fuel control and post catalyst monitoring. Each HO2S compares the oxygen content of the surrounding air with the oxygen content in the exhaust stream. The HO2S must reach operating temperature to provide an accurate voltage signal. Heating elements inside the HO2S minimize the time required for the sensors to reach operating temperature. The powertrain control module (PCM) supplies the HO2S with a reference, or bias, voltage of about 450 mV . When the engine is first started the PCM operates in Open Loop, ignoring the HO2S voltage signal. Once the HO2S reaches operating temperatures and Closed Loop is achieved, the HO2S generates a voltage within a range of 0-1,000 mV that fluctuates above and below bias voltage. High HO2S voltage indicates a rich exhaust stream. Low HO2S voltage indicates a lean exhaust stream.

If the PCM detects an HO2S voltage that stays below a specified value, DTC P0137 will set.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0137 HO2S Circuit Low Voltage Sensor 2

Conditions for Running the DTC

DTCs P0068, P0106, P0107, P0108, P0112, P0113, P0117, P0118, P0120, P0122, P0123, P0125, P0128, P0201, P0202, P0203, P0204, P0205, P0206, P0220, P0300-P0306, P0315, P0336, P0442, P0446, P0452, P0453, P0455, P0483, P0496, P0506, P0507, P0601, P0602, P0604, P0606, P060D, P060E, P0641, P0651, P1516, P1621, P2101, P2120, P2125, P2135, P2138, P2176 are not set.
The Engine Coolant Temperature (ECT) Sensor parameter is more than 70°C (158°F) .
The Ignition 1 Signal parameter is more than 10 volts .
The Fuel Level Sensor parameter is more than 10 percent .
The Engine Run Time parameter is more than 10 seconds .
The Loop Status parameter is closed.
The Throttle Position (TP) Indicated Angle parameter is between 15-50 percent .
The Manifold Absolute Pressure (MAP) Sensor parameter is more than 25 kPa .
The Accelerator Pedal Position (APP) Indicated Angle parameter is more than 1.2 percent .
DTC P0137 runs continuously when the above conditions are met for 4 seconds .
Conditions for Setting the DTC

The PCM detects that the HO2S 2 parameter is less than 43 mV .
DTC P0137 sets within 150 seconds when the above condition is met.
Action Taken When the DTC Sets

The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.
Conditions for Clearing the MIL/DTC

The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
Clear the MIL and the DTC with a scan tool.
Записан

москвич

  • Модератор Форума
  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 50
  • Пол: Мужской
  • Сообщений: 9905
  • Автомобиль: на капоте трех лучевая звезда....GLS 350...была птаха 900 8 года белая Z-71 для города...для грязи ГАЗ66
  • Имя: Василий
  • а нахера(С)
  • Местоположение: колхоз столица
  • Карма: +523/-13
Спасите, 05.09 ехать 700 км!
« Ответ #8 : 05 сентября 2012, 13:04:11 »

константин..... ..ты вроде из москвы.....а это значит что по русски должен писать......... а взял и выложил на англицком писанину какую то.......переве сти в гугле не получилось?...
Записан
   
мы можем сверху,снизу,сбоку...а также спереди и сзади

johnyelc

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Пол: Мужской
  • Сообщений: 177
  • Автомобиль: TrailBlazer 2002
  • Имя: Евгений
  • +79529460404
  • Местоположение: г. Новосибирск
  • Карма: +0/-0
Спасите, 05.09 ехать 700 км!
« Ответ #9 : 05 сентября 2012, 22:39:47 »

Спасибо всем кто откликнулся. ;)
В общем через 3 часа в путь, дело обстоит так.
Вчера к вечеру заметил сумасшедший расход и на холостых оборотах 900 держит.
Утром поехал обратно в сервис, ребята посмотрели заново сваренный глушак на наличие дырок, дырок нет, обманка сказали правильная, все собрали, ошибка пропала я уехал все норм, пройдя 10 км, снова все по старой, вернулся стали разбираться, отключаем 1-ю лямбду, все нормализуется. 1 лямбда была до этого приварена не герметично и видимо что то повредили давно + трещина на коллекторе, но до вчерашнего этих ошибок не было(((, было принято решение приварить намертво эту лямбду, вырезать в трубе дырку и прикрутить туда новую что и было сделано, после 900 оборотный режим пропал, остались ошибки p0134 и p0130, с обеда чек не горит но эти ошибки в стадии рассмотрения по компьютеру... Как сказали ребята, я купил лямбду универсальную и там время нагрева что ли не тот, надо покупать оригинальную и все будет норм, если есть какие то соображения по этому поводу буду благодарен.
По работе:
замена катализатора на пламегаситель с обманкой: 4.500 + 900 рублей приварили трубу, т.к. задняя банка отвалилась(((
2.000 рублей лямбда + 2.000 работа по внедрению.
В общем не получилось сэкономить на поездке((((((   =)))))
Записан

mvi

  • Майор
  • *
  • Оффлайн Оффлайн
  • Возраст: 49
  • Пол: Мужской
  • Сообщений: 963
  • Автомобиль: Trailblazer 2006 г.LTZ, цвет вороной, Форд Куга 2 Rest,Toyota Sprinter Trueno 88 г.в., и много Яв ))
  • Имя: Вячеслав
  • Местоположение: Иваново
  • Карма: +100/-0
Спасите, 05.09 ехать 700 км!
« Ответ #10 : 05 сентября 2012, 23:03:03 »

А зачем ты его менял?? Трыл такая машина - не ломается не трож! Теперь борись с ошибками. Удачи!
Записан
Всё, что ни делается - всё к лучшему, главное сделать правильные выводы!

johnyelc

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Пол: Мужской
  • Сообщений: 177
  • Автомобиль: TrailBlazer 2002
  • Имя: Евгений
  • +79529460404
  • Местоположение: г. Новосибирск
  • Карма: +0/-0
Спасите, 05.09 ехать 700 км!
« Ответ #11 : 05 сентября 2012, 23:30:42 »

Была ошибка по катализатору, p0420, вот и решил к бабе фене его, а потом целая грядка вылезла, гребаные датчики эти, уже не знаю чего менять то надо, думаю, может расход воздуха или чего уже, замучался, устал((, нет однозначных ответов, проще к бабке гадалке сходить и то может вероятнее будет(((( :'(
Записан

Виталий

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 47
  • Пол: Мужской
  • Сообщений: 4943
  • Автомобиль: ТБ, 2005
  • Имя: Виталий
  • Местоположение: МО г. Подольск
  • Карма: +211/-4
Спасите, 05.09 ехать 700 км!
« Ответ #12 : 05 сентября 2012, 23:58:03 »

А хде делал?
Записан
Бываю редко, если что пишите в личку.......

johnyelc

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Пол: Мужской
  • Сообщений: 177
  • Автомобиль: TrailBlazer 2002
  • Имя: Евгений
  • +79529460404
  • Местоположение: г. Новосибирск
  • Карма: +0/-0
Спасите, 05.09 ехать 700 км!
« Ответ #13 : 21 сентября 2012, 12:57:35 »

делали в автоглушаке., неужели лямбда такая привередливая, нужно ориджинал брать только?
Записан

Виталий

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 47
  • Пол: Мужской
  • Сообщений: 4943
  • Автомобиль: ТБ, 2005
  • Имя: Виталий
  • Местоположение: МО г. Подольск
  • Карма: +211/-4
Спасите, 05.09 ехать 700 км!
« Ответ #14 : 21 сентября 2012, 13:16:30 »

Странно, с ними проблем никогда не было, я уже больше года катаюсь и все нормуль. Езжай пусть переделывают. Или может у тебя лямбда вторая загнулась.
Записан
Бываю редко, если что пишите в личку.......

johnyelc

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Пол: Мужской
  • Сообщений: 177
  • Автомобиль: TrailBlazer 2002
  • Имя: Евгений
  • +79529460404
  • Местоположение: г. Новосибирск
  • Карма: +0/-0
Спасите, 05.09 ехать 700 км!
« Ответ #15 : 21 сентября 2012, 13:22:00 »

да сказали надо ориджинал лямбду купить на перед, тогда будет все гуд, посмотрим...
Записан

makTM

  • Ст. Прапорщик
  • *
  • Оффлайн Оффлайн
  • Пол: Мужской
  • Сообщений: 240
  • Автомобиль: TrailBlazer 2005г.
  • Имя: Николай
  • Местоположение: Якутск
  • Карма: +5/-0
Re: Спасите, 05.09 ехать 700 км!
« Ответ #16 : 21 марта 2014, 17:33:02 »

и чем закончилось все?
Записан

Renegade

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 49
  • Пол: Мужской
  • Сообщений: 4651
  • Автомобиль: Escalade
  • Имя: Не помню
  • Местоположение: Москва
  • Карма: +229/-27
Re: Спасите, 05.09 ехать 700 км!
« Ответ #17 : 21 марта 2014, 18:24:31 »

делали в автоглушаке., неужели лямбда такая привередливая, нужно ориджинал брать только?
Ребята вроде нормальные....а то же у них с глушаками все делал..........
Записан
Бывают такие решения..... после принятия которых..... тараканы в голове аплодируют стоя!

Богу верю.... за остальными слежу