Российский Клуб Chevrolet TrailBlazer & Chevrolet Tahoe

Автор Тема: КОДЫ ОШИБОК OBD 2 ===расшифровка и решение проблем===  (Прочитано 382977 раз)

0 Пользователей и 1 Гость просматривают эту тему.

Бэтман

  • Генерал-полковник
  • *
  • Оффлайн Оффлайн
  • Возраст: 45
  • Пол: Мужской
  • Сообщений: 2330
  • Автомобиль: SSANG белый 773
  • Бэтман
  • Местоположение: ЮАО, чертаново
  • Карма: +115/-0

Может под эти штуки сделать маленькую тему и прикрепить..... .....дабы не потерялась..... .....и львиная доля вопросов "А что это у меня случилось" или "Подскажите что это за ошибка?" думаю отпадет сама собой.........

Так это еще надо перевести на русский язык ( не многие поймут, что там написано
Записан
X

trail415->109

  • Рядовой
  • *
  • Оффлайн Оффлайн
  • Пол: Женский
  • Сообщений: 15
  • Автомобиль: был TrailBlazer 2007 г. стал TrailBlazer 2009 )
  • Имя: Светлана
  • Местоположение: Санкт-Петербург
  • Карма: +0/-0

Приветствую
подскажите, а какой вы программой смотрите ошибки? и по какому протоколу?
просто купили адаптер obd2-usb (орион) , а подключиться никак не можем :(
Записан
"Всё, что я должен, написано в Налоговом кодексе. Что не должен - в Уголовном. Все остальное - чьи-то домыслы" (с)

Konfety

  • Команда Модераторов
  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 50
  • Пол: Мужской
  • Сообщений: 6194
  • Имя: Дмитрий
  • Клубный сервис в Санкт- Петербурге
  • Местоположение: СПБ Пискаревский 144 ар
  • Карма: +220/-5

Я когда адаптер покупал, диск с прогами дали, хочеш скину тебе, давай куда кидать.
Записан



Наше мобильное приложение! =====> БОНУСНАЯ СИСТЕМА

trail415->109

  • Рядовой
  • *
  • Оффлайн Оффлайн
  • Пол: Женский
  • Сообщений: 15
  • Автомобиль: был TrailBlazer 2007 г. стал TrailBlazer 2009 )
  • Имя: Светлана
  • Местоположение: Санкт-Петербург
  • Карма: +0/-0

Я когда адаптер покупал, диск с прогами дали, хочеш скину тебе, давай куда кидать.
Спасибо, нашли и подключили, оказалось что сначала кабель не тот купили :)
Записан
"Всё, что я должен, написано в Налоговом кодексе. Что не должен - в Уголовном. Все остальное - чьи-то домыслы" (с)

maikl

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 57
  • Пол: Мужской
  • Сообщений: 4351
  • Трылик стероидный, и просто ТАХ белый
  • Местоположение: Питер Приморский р-н
  • Карма: +168/-6

 Народ! Кто знает, что за ошибка 2444?? Расшифровки не нашел..
Записан

Temich

  • Лейтенант
  • *
  • Оффлайн Оффлайн
  • Возраст: 43
  • Пол: Мужской
  • Сообщений: 389
  • Автомобиль: Skoda Octavia Scout
  • Имя: Артем
  • Местоположение: СПб
  • Карма: +15/-4
Записан

maikl

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 57
  • Пол: Мужской
  • Сообщений: 4351
  • Трылик стероидный, и просто ТАХ белый
  • Местоположение: Питер Приморский р-н
  • Карма: +168/-6

Спасибо!! Вот только на айпаде  меня нетпереводчика((
Еще до кучи выскочила 2431 ошибка! Я так понимаю это связано с ЕГР и с выхлопными газами??
Записан

Temich

  • Лейтенант
  • *
  • Оффлайн Оффлайн
  • Возраст: 43
  • Пол: Мужской
  • Сообщений: 389
  • Автомобиль: Skoda Octavia Scout
  • Имя: Артем
  • Местоположение: СПб
  • Карма: +15/-4
Записан

Konfety

  • Команда Модераторов
  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 50
  • Пол: Мужской
  • Сообщений: 6194
  • Имя: Дмитрий
  • Клубный сервис в Санкт- Петербурге
  • Местоположение: СПБ Пискаревский 144 ар
  • Карма: +220/-5

Миша это все система вторичного воздуха........ ....которая у тебя под задницей на раме

P2444  Ткни меня

P2431  Ткни меня
Записан



Наше мобильное приложение! =====> БОНУСНАЯ СИСТЕМА

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0

DTC P2444

Pump relay coil control  - Short to ground
Circuit/System Description

The secondary air injection (AIR) system aids in the reduction of hydrocarbon emissions during a cold start. The system forces fresh filtered air into the exhaust stream in order to accelerate the catalyst operation. An electric air pump, the secondary AIR injection pump, provides filtered air on demand to the AIR control solenoid valve/pressure sensor assembly. The AIR control solenoid valve/pressure sensor assembly controls the flow of air from the AIR pump to the exhaust manifold. The AIR valve relay supplies the current needed to operate the AIR control solenoid valve/pressure sensor assembly. A pressure sensor is used to monitor the air flow from the AIR pump. The powertrain control module (PCM) supplies the internal pressure sensor with a 5-volt reference, an electrical ground, and a signal circuit.

The AIR diagnostic uses 3 phases to test the AIR system:

DTCs P0411 and P2430 run during Phase 1
DTCs P2430 and P2440 run during Phase 2
DTC P2444 runs during Phase 3

During phase 1, both the AIR pump and the solenoid valve are activated. Normal secondary air function occurs. Expected system pressure is 8-10 kPa above barometric pressure (BARO).

During phase 2, only the AIR pump is activated. The solenoid valve is closed. Pressure sensor performance and solenoid valve deactivation are tested. Expected system pressure is 20-25 kPa above BARO.

During phase 3, neither the AIR pump nor the solenoid valve is activated. AIR pump deactivation is tested. Expected system pressure equals BARO.

In all 3 phases, testing is accomplished by comparing the measured pressure against the expected pressure. The PCM can detect faults in the AIR pump, AIR control solenoid valve/pressure sensor assembly, and the exhaust check valve. The pressure sensor can also detect leaks and restrictions in the secondary AIR system plumbing.

Conditions for Running the DTC

DTCs P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0125, P0128, P0201, P0202, P0203, P0204, P0300, P0412, P0418, P0420, P0606, P1106, P1107, P1111, P1112, P1114, P1115, P1635, P1639, P2430, P2431, P2432, P2433 are not set.
More than 60 minutes has elapsed since the last cold start.
The system voltage is 9-18 volts .
The BARO parameter is more than 70 kPa .
The MAF sensor parameter is less than 33 g/s .
The AIR system is commanded ON.
The conditions are stable for more than 5 seconds .
DTC P2444 runs once per trip start up when the above conditions are met and AIR pump operation is requested.

Your Vehicle: 2007 Chevy Truck TrailBlazer 4WD L6-4.2L
    
Vehicle » Powertrain Management » Computers and Control Systems » Testing and Inspection » Diagnostic Trouble Code Tests and Associated Procedures » P Code Charts » P2444   
 
 
    P2444   
 
DTC P2444

Diagnostic Instructions

Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. See: Testing and Inspection\Initial Inspection and Diagnostic Overview
Strategy Based Diagnosis for an overview of the diagnostic approach.
Diagnostic Procedure Instructions provide an overview of each diagnostic category.
DTC Descriptor

DTC P2444
Secondary Air Injection (AIR) System Pump Stuck On

   
Diagnostic Fault Information


   
Typical Scan Tool Data

Circuit/System Description

The secondary air injection (AIR) system aids in the reduction of hydrocarbon emissions during a cold start. The system forces fresh filtered air into the exhaust stream in order to accelerate the catalyst operation. An electric air pump, the secondary AIR injection pump, provides filtered air on demand to the AIR control solenoid valve/pressure sensor assembly. The AIR control solenoid valve/pressure sensor assembly controls the flow of air from the AIR pump to the exhaust manifold. The AIR valve relay supplies the current needed to operate the AIR control solenoid valve/pressure sensor assembly. A pressure sensor is used to monitor the air flow from the AIR pump. The powertrain control module (PCM) supplies the internal pressure sensor with a 5-volt reference, an electrical ground, and a signal circuit.

The AIR diagnostic uses 3 phases to test the AIR system:

DTCs P0411 and P2430 run during Phase 1
DTCs P2430 and P2440 run during Phase 2
DTC P2444 runs during Phase 3
During phase 1, both the AIR pump and the solenoid valve are activated. Normal secondary air function occurs. Expected system pressure is 8-10 kPa above barometric pressure (BARO).

During phase 2, only the AIR pump is activated. The solenoid valve is closed. Pressure sensor performance and solenoid valve deactivation are tested. Expected system pressure is 20-25 kPa above BARO.

During phase 3, neither the AIR pump nor the solenoid valve is activated. AIR pump deactivation is tested. Expected system pressure equals BARO.

In all 3 phases, testing is accomplished by comparing the measured pressure against the expected pressure. The PCM can detect faults in the AIR pump, AIR control solenoid valve/pressure sensor assembly, and the exhaust check valve. The pressure sensor can also detect leaks and restrictions in the secondary AIR system plumbing.

Conditions for Running the DTC

DTCs P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0125, P0128, P0201, P0202, P0203, P0204, P0300, P0412, P0418, P0420, P0606, P1106, P1107, P1111, P1112, P1114, P1115, P1635, P1639, P2430, P2431, P2432, P2433 are not set.
More than 60 minutes has elapsed since the last cold start.
The system voltage is 9-18 volts .
The BARO parameter is more than 70 kPa .
The MAF sensor parameter is less than 33 g/s .
The AIR system is commanded ON.
The conditions are stable for more than 5 seconds .
DTC P2444 runs once per trip start up when the above conditions are met and AIR pump operation is requested.
Conditions for Setting the DTC

The measured AIR pressure is more than expected.
DTC P2444 sets within 5 seconds when the above condition is met.
Action Taken When the DTC Sets

DTC P2444 is a type A DTC.

Conditions for Clearing the MIL/DTC

DTC P2444 is a type A DTC.

Circuit/System Verification

If DTCs P0411, P0418, P2432 or P2433 are set, perform those diagnostics first.
Ignition ON, observe that the AIR pump is not activated.
¤   If the AIR pump is activated, test the AIR pump voltage supply circuit for a short to voltage. If the circuit tests normal, test the AIR pump relay control circuit for a short to ground. If the circuits test normal, test the relay. If the circuits and relay test normal, replace the PCM.
Component Testing

Relay Test
Test between the normally-closed switch terminals, if any, for 0 ohms .
Test between the normally-open switch terminals for infinite ohms.
Test between each switch terminal and either coil terminal for infinite ohms.
Connect the relay coil terminals to ground and fused power to energize the relay.
Test between each switch terminal and each coil terminal for 0 volts .
Test between the normally-closed switch terminals, if any, for infinite ohms.
Test between the normally-open switch terminals for 0 ohms .
Repair Instructions

Secondary Air Injection Pump Replacement
Secondary Air Injection Solenoid Valve Replacement
Secondary Air Injection Pump Hose Replacement
Control Module References for control module replacement, setup and programming See: Testing and Inspection\Programming and Relearning
Repair Verification

With the ignition ON and the engine OFF, observe that the AIR pump is not operating.
Записан

Konfety

  • Команда Модераторов
  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 50
  • Пол: Мужской
  • Сообщений: 6194
  • Имя: Дмитрий
  • Клубный сервис в Санкт- Петербурге
  • Местоположение: СПБ Пискаревский 144 ар
  • Карма: +220/-5

Щас у Мищи мозг вскипит........ .... ;D ;D ;D
Записан



Наше мобильное приложение! =====> БОНУСНАЯ СИСТЕМА

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0

DTC P2431

Presure sensor 5 volt reference voltage - Short to voltage

Circuit/System Description

The secondary air injection (AIR) system aids in the reduction of hydrocarbon emissions during a cold start. The system forces fresh filtered air into the exhaust stream in order to accelerate the catalyst operation. An electric air pump, the secondary AIR injection pump, provides filtered air on demand to the AIR control solenoid valve/pressure sensor assembly. The AIR control solenoid valve/pressure sensor assembly controls the flow of air from the AIR pump to the exhaust manifold. The AIR solenoid valve relay supplies the current needed to operate the AIR solenoid valve/pressure sensor assembly. A pressure sensor is used to monitor the air flow from the AIR pump. The powertrain control module (PCM) supplies the internal pressure sensor with a 5-volt reference, an electrical ground, and a signal circuit.

The AIR diagnostic uses 3 phases to test the AIR system:

DTCs P0411 and P2430 run during Phase 1
DTCs P2430 and P2440 run during Phase 2
DTC P2444 runs during Phase 3
During phase 1, both the AIR pump and the solenoid valve are activated. Normal secondary air function occurs. Expected system pressure is 8-10 kPa above barometric pressure (BARO).

During phase 2, only the AIR pump is activated. The solenoid valve is closed. Pressure sensor performance and solenoid valve deactivation are tested. Expected system pressure is 20-25 kPa above BARO.

During phase 3, neither the AIR pump nor the solenoid valve is activated. AIR pump deactivation is tested. Expected system pressure equals BARO.

In all 3 phases, testing is accomplished by comparing the measured pressure against the expected pressure. The PCM can detect faults in the AIR pump, AIR solenoid valve/pressure sensor assembly, and the exhaust check valve. The pressure sensor can also detect leaks and restrictions in the secondary AIR system plumbing.

Conditions for Running the DTC

DTCs P0106, P0107, P0108, P0412, P0418, P0606, P1635, P1639, P2432, P2433 are not set.
The ignition is ON.
DTC P2431 runs continuously when the above conditions are met.
Conditions for Setting the DTC

The PCM determines that the difference between the AIR pressure sensor and the BARO sensor signals is greater than 10 kPa when the AIR pump is commanded OFF.

OR

The PCM determines that the difference between the AIR pressure sensor and the BARO sensor signals is greater than 50 kPa when the AIR pump is commanded ON.

Action Taken When the DTC Sets

DTC P2431 is a type B DTC.

Conditions for Clearing the MIL/DTC

DTC P2431 is a type B DTC.

Circuit/System Verification

Engine running, observe that the AIR Pressure Sensor parameter approximately equals BARO.

Circuit/System Testing

Ignition OFF, disconnect the harness connector at the AIR solenoid valve.
Ignition OFF, test for less than 1 ohm of resistance between the low reference circuit terminal 1 and ground.
¤   If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the PCM.
Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal 3 and ground.
¤   If less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the PCM.
¤   If greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the PCM.
Verify the scan tool AIR Pressure Sensor parameter is less than 0.5 volt .
¤   If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the PCM.
Install a 3A fused jumper wire between the signal circuit terminal 2 and the 5-volt reference circuit terminal 3. Verify the scan tool AIR Pressure Sensor parameter is greater than 4.9 volts .
¤   If less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the PCM.
If all circuits test normal, test or replace the AIR solenoid valve.
Component Testing
Solenoid Valve

Apply fused battery voltage and ground to the solenoid and verify that the valve opens and closes completely as voltage is applied to and removed from the solenoid. Observe that the valve is not obstructed or leaking.

If the valve operates incorrectly, leaks, or is obstructed, remove the obstruction or replace the valve.

Repair Instructions

Secondary Air Injection Pump Replacement
Secondary Air Injection Solenoid Valve Replacement
Secondary Air Injection Pump Hose Replacement
Control Module References for control module replacement, setup and programming See: Testing and Inspection\Programming and Relearning
Repair Verification

With the key ON and the engine OFF, observe that the AIR Pressure Sensor parameter is approximately equal to BARO.
With the engine running, enable the AIR pump with a scan tool and observe that the AIR Pressure Sensor parameter equals approximately 20-25 kPa above BARO.
With the engine running, enable the AIR Solenoid with a scan tool and observe that the AIR Pressure Sensor parameter equals approximately 8-10 kPa above BARO.
Записан

Konstantin

  • Старшина
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 171
  • Автомобиль: Chevrolet Tahoe 900
  • Местоположение: Москва, ЮВАО
  • Карма: +17/-0

P2444  - Pump relay coil control  - Short to ground  \ Реле насоса - Короткое замыкание на землю

P2431  - Presure sensor 5 volt reference voltage - Short to voltage \ Датчик давления  (в части 5 вольтового опорного напряжения) - короткое замыкание  либо потеря напряжения.)

Это первичные возможные причины
Записан

maikl

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 57
  • Пол: Мужской
  • Сообщений: 4351
  • Трылик стероидный, и просто ТАХ белый
  • Местоположение: Питер Приморский р-н
  • Карма: +168/-6

Мозги вскипели!! Переводчика нет. На что влияют эти датчики?? Только при запуске, или на прогретом движке тож?? Кататься то можно??
Записан

Konfety

  • Команда Модераторов
  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 50
  • Пол: Мужской
  • Сообщений: 6194
  • Имя: Дмитрий
  • Клубный сервис в Санкт- Петербурге
  • Местоположение: СПБ Пискаревский 144 ар
  • Карма: +220/-5

Ну не будет у тебя каталик продувать пока........... ..у меня тоже по этой системе ошибка присутствует... ........правда и каталика давно нет...........
Записан



Наше мобильное приложение! =====> БОНУСНАЯ СИСТЕМА

maikl

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 57
  • Пол: Мужской
  • Сообщений: 4351
  • Трылик стероидный, и просто ТАХ белый
  • Местоположение: Питер Приморский р-н
  • Карма: +168/-6

Выскочила сегодня :(
P0411 Неправильно отрегулирован расход во впускном коллекторе 
Может из-за заглушенного клапана вторичноговозду ха ???
Записан

Konfety

  • Команда Модераторов
  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 50
  • Пол: Мужской
  • Сообщений: 6194
  • Имя: Дмитрий
  • Клубный сервис в Санкт- Петербурге
  • Местоположение: СПБ Пискаревский 144 ар
  • Карма: +220/-5

Выскочила сегодня :(
P0411 Неправильно отрегулирован расход во впускном коллекторе
Может из-за заглушенного клапана вторичноговозду ха ???

А датчик, который на коллекторе сидит.......... ..ничего попутать не мог??..............
Записан



Наше мобильное приложение! =====> БОНУСНАЯ СИСТЕМА

maikl

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 57
  • Пол: Мужской
  • Сообщений: 4351
  • Трылик стероидный, и просто ТАХ белый
  • Местоположение: Питер Приморский р-н
  • Карма: +168/-6

А фиг его знает! Вот и хотелось бы знать, из- за вторричного клапана или в датчике проблема...Попр обую скинуть на горячем движке ошибку и посмотрим как отреагируют мозги.
Записан

Konfety

  • Команда Модераторов
  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 50
  • Пол: Мужской
  • Сообщений: 6194
  • Имя: Дмитрий
  • Клубный сервис в Санкт- Петербурге
  • Местоположение: СПБ Пискаревский 144 ар
  • Карма: +220/-5

Слушай......у меня постоянно ошибка выскакивает по вторичному воздуху........ но других нет....поэтому так и подумал.
Записан



Наше мобильное приложение! =====> БОНУСНАЯ СИСТЕМА

maikl

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 57
  • Пол: Мужской
  • Сообщений: 4351
  • Трылик стероидный, и просто ТАХ белый
  • Местоположение: Питер Приморский р-н
  • Карма: +168/-6

До кучи вискочила ошибка 2432  ??? ???
Записан

Konfety

  • Команда Модераторов
  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 50
  • Пол: Мужской
  • Сообщений: 6194
  • Имя: Дмитрий
  • Клубный сервис в Санкт- Петербурге
  • Местоположение: СПБ Пискаревский 144 ар
  • Карма: +220/-5

http://www.obd2code.ru/getcode.html?code=P2432&brand=1
Я так понял, на массу замыкает, что то из этой системы.
Записан



Наше мобильное приложение! =====> БОНУСНАЯ СИСТЕМА

maikl

  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 57
  • Пол: Мужской
  • Сообщений: 4351
  • Трылик стероидный, и просто ТАХ белый
  • Местоположение: Питер Приморский р-н
  • Карма: +168/-6

Тож есть такие подозрения. Буду прозванивать ...
Записан

Manrokh

  • Мл. Лейтенант
  • *
  • Оффлайн Оффлайн
  • Возраст: 45
  • Пол: Мужской
  • Сообщений: 333
  • Местоположение: Санкт-Петербург
  • Карма: +15/-0

Дорогие друзья подскажите пожалуйста по Р0128: изучил темы в основном лечится заменой термостата, а мне на сервисе рекомендуют поменять датчик температуры охлаждающей жидкости, в СПб в наличии его нигде нет - следовательно это совсем неходовая запчасть... Так вот вопрос: он вообще может сломаться? У кого нибудь ломался? Есть смысл его менять или только менять термостат? (машина прогревается быстро, но температура по стрелке обычно меньше 100 ( на глаз 86-90)).
Записан

ultra174

  • Лейтенант
  • *
  • Оффлайн Оффлайн
  • Возраст: 52
  • Пол: Мужской
  • Сообщений: 413
  • Имя: Вадим
  • Местоположение: Тамбовская область
  • Карма: +20/-2

Дорогие друзья подскажите пожалуйста по Р0128: изучил темы в основном лечится заменой термостата, а мне на сервисе рекомендуют поменять датчик температуры охлаждающей жидкости, в СПб в наличии его нигде нет - следовательно это совсем неходовая запчасть... Так вот вопрос: он вообще может сломаться? У кого нибудь ломался? Есть смысл его менять или только менять термостат? (машина прогревается быстро, но температура по стрелке обычно меньше 100 ( на глаз 86-90)).
датчик вряд ли... Если только проводка до него... Если есть сомнения в датчике, подключи тестер, на нем сопротивление меняется в зависимости от температуры.
( 0*С ~ 5,9кОм,
20*С ~ 2,5кОм,
40*С ~ 1,2кОм,
60*С ~ 0,7кОм,
70*С ~ 0.45кОм,
80*С ~ 0,33кОм,
90*С ~ 0,24кОм,
100*С ~ 0.17кОм)
Записан

vv051

  • Гость
  • Карма: +/-

Доброго дня,подскажите пожалуйста,периодически (уже три раза за неделю) стала выскакивать ошибка P0420 Низкая эффективность работы нейтрализатора. Это приговор катализатору или есть еще какие нибудь причины возникновения этой ошибки?
« Последнее редактирование: 13 мая 2012, 15:56:32 от Vladimir51 »
Записан

Aleksey1975

  • Мл. сержант
  • *
  • Оффлайн Оффлайн
  • Возраст: 51
  • Пол: Мужской
  • Сообщений: 67
  • Автомобиль: ТБ 2005, чорний
  • Имя: Алексей
  • Местоположение: Пенза
  • Карма: +4/-3

Р0204, 206
Р0172
Р0300
Р0420
Это понятно, Но Р0017 откуда? Сбросили ошибки - появилось всё верхнее вновь,а 17 пропало.
Стоят новые свечи все, катушки 4 и 6-го горшков, форсунки мыл сам, все клацали.. Какова вероятность проблем в проводке? У меня ГБО стоит да и так хрен долезешь до разъёмов форсунок. Сколько должно быть сопротивление обмток? Могу промерить не залезая в дебри?..
Мировой разум, куда все делись?
А ещё по утрам на холодную стучит какой-то гидрик, собако
Записан
Иномарки не ломаюца!

kott1987

  • Капитан
  • *
  • Оффлайн Оффлайн
  • Возраст: 39
  • Пол: Мужской
  • Сообщений: 670
  • Автомобиль: TrailBlazer 4200
  • Имя: Дмитрий
  • Местоположение: Воронеж
  • Карма: +14/-1

Ошибка 1174 покоя не дает.
Что это?как боротся?на сто влияет?
Записан

andrei-kamensk

  • Мл. сержант
  • *
  • Оффлайн Оффлайн
  • Пол: Мужской
  • Сообщений: 62
  • Автомобиль: chevrolet
  • Местоположение: каменск
  • Карма: +0/-0

выскочила ошибка р2101 что это?и как бороться?
Записан

Макс_SPb

  • Модератор Этого Раздела
  • Ветеран клуба
  • *
  • Оффлайн Оффлайн
  • Возраст: 46
  • Пол: Мужской
  • Сообщений: 6043
  • Автомобиль: Серый бегемот 07 + тройка черная
  • В России можно жить либо хорошо, либо по закону.
  • Местоположение: Питер
  • Карма: +268/-24
Записан
Не бойтесь, что вас обведут вокруг пальца, бойтесь, что вас обведут мелом.
Если Вам кажется, что у меня опустились руки - вы ошибаетесь. Я наклонился за монтировкой!
Цени того, кто на твои вопросы спросит "Чем помочь?"

Aleksey1975

  • Мл. сержант
  • *
  • Оффлайн Оффлайн
  • Возраст: 51
  • Пол: Мужской
  • Сообщений: 67
  • Автомобиль: ТБ 2005, чорний
  • Имя: Алексей
  • Местоположение: Пенза
  • Карма: +4/-3

Замечательный пост. Как в колодец бросаем коды, нафик отвечать? Вот вам расшифровка (в очереднойраз), иптесь сами, а у нас отпуск, и вообще - Иномарки  не ломаюца... во, сменю подпись!
Записан
Иномарки не ломаюца!